Monel 400 pipe for marine fixtures pumps and valves

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

2.4375 Monel K500 round bar is non-magnetic, as an alloy, Monel K500 ASTM B865 hexagonal bar exhibits excellent mechanical properties over a temperature range from sub-zero settings to 480C. Monel ASTM B865 hollow bars require annealing when welded, and weldments should be stress relieved to the alloy prior to aging.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

Nickel alloys are combinations of nickel and a variety of other metals that make strong, oxidation-resistant products with an average lifespan of 25 to 35 years. Monel 400 is a nickel-copper alloy containing approximately 67% nickel and 23% copper.

Monel 400 and K500 flanges also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions.

Monel K-500 combines the excellent corrosion resistance of Monel 400 with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni 3 (Ti, Al) throughout the matrix.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Alloy 400 Seamless Pipe exhibits excellent resistance to not only caustic solutions but also brine and seawater, which makes it perfect for marine applications.

Monel 400 is resistant to both steam and seawater as well as highly caustic solutions such as sulfuric, hydrochloric, and hydrofluoric acids when they are deaerated.

NAS625 (NCF625, UNS N06625) is a nickel-chromium-molybdenum alloy with an additional of niobium. Matrix stiffening provided by molybdenum and niobium results in high strength. The alloy resists a wide range of severe corrosion environments. It also offers resistance to high temperatures. It also demonstrates remarkable protection against corrosion and oxidation. Its ability to withstand high stress and a wide range of temperatures, both in and out of water, as well as being able to resist corrosion while being exposed to highly acidic environments makes it a fitting choice for nuclear and marine applications.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements. HT PIPE is a leading manufacturer of Monel K500 Bolts and Nuts of all types and sizes. Fastener applications include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, pharmaceuticals, equipment, seawater applications, heat exchangers, condensers, and the pulp and paper industry.

Monel K500 steel bars are particularly suitable for centrifugal pumps in the marine industry. This is due to the properties of Monel N05500 hot rolled bar, namely high tensile strength and low corrosion rate in high velocity seawater.

Monel 400 is a kind of corrosion resistant alloy with large dosage

The Monel K500 flanges available in our company are customized in designs, sizes and shapes. The specification of these flanges is ASTM B564. These flanges range in size from 1/8 inches to 48 inches.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

Alloy 400 (UNS N04400) is a nickel-copper alloy with high strength (comparable to structural steel) and toughness.

Monel 400 Butt Weld Reducers are resistant to aggressive solvents, acids and bases, and seawater, are highly robust at high temperatures, and are also operable for use in many marine engineering applications.

Monel 400 Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

Monel 400 is well known for its high strength and corrosion resistant properties. It works in a wide range of temperatures, and is available in multiple forms for a variety of products. Monel 400 is used extensively in (for pipe) piping. Resistant to both steam and seawater, its toughness and anti-corrosive properties make it perfect for heavy duty applications such as transfer (pipe) piping used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Monel 400 Bolts and Nuts are made from a nickel-copper alloy for extreme corrosion resistance, especially in sour conditions. The material is also strong and rigid and can be used to produce bolts and nuts for high temperature service. HT PIPE is a leading manufacturer and supplier of Monel 400 Bolts and Nuts of all sizes and types. Among the ingredients are carbon, aluminum, manganese, silicon, iron, sulfur and 63% nickel and 28% copper. This composition gives the material a high melting point.

Monel K500 pipe bend and elbow are resistant to a sour-gas environment

At room temperature settings, Monel 400 exhibits slight magnetic behavior, thus, the use of WNR 2.4360 Reducing Flange could also be extended to applications that require magnetic characteristics to a certain degree.

It combines the corrosion resistance of Monel K-500 but gives the added advantage of extra strength and hardness (as a result of its age hardening ability).

MONEL? alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy which combines the excellent corrosion resistance of MONEL alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base.

The hex head design of the Monel bolt also allows the wrench to easily grasp it, improving the tightening and loosening experience. Monel k500 ASTM material provides advanced quality corrosion protection from hydrofluoric acid, salts, alkalinity and more. Monel NiCu k500 hex bolts are also resistant to seawater and steam, so they are a solid choice for marine applications.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Our wide array of UNS N05500 | Monel K500 Threaded Flanges is utilize in rough oil stills, gas and new water tanks, marine installations and clasp, and concoction preparing gear.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.