ASME A105 forged fitting 3000psi NPT thread equal tee cross

ASTM A105 covers forged carbon steel flanges and piping components for ambient and high temperature service in pressure systems. It also includes fittings, valves and similar parts. The maximum weight of manufactured forgings to which this standard follows is 10,000 circles (4,540kg). Larger forgings can be made in accordance with Standard A 266/A266M. This specification does not cover tube sheets and hollow cylindrical forgings for pressure vessel shells.

A234 WPB steel pipe fittings mean the pipe fitting which material is ASTM A234 WPB,they are used for the pressure piping systems of moderate and high temperature services.

The elbow is used to turn the direction of a pipe line regularly by 90 degrees angle.These pipe fittings used in pressure pipelines and pressure vessel fabrication for servic at moderate and increased temperatures. Fittings out of above standards shall be complied with A960/A960M.

A105 shall adhere to tensile strength, yield strength, elongation, reduction of area, and hardness requirements. Guidelines for retreatment, repair by welding, and product marking are given.

ASTM A105 covers forged carbon steel flange and piping components for ambient and higher-temperature administration in pressure systems

ASTM A234 WPB short radius in accordance with ASME B16.9.Carbon steel pipe fittings manufactured to ASMT A234 are usually furnished in the butt-welding form in accordance with ASME B16.9 or ASME B16.49.

A105 steel is one of the most commonly used carbon steel material grades for the manufacture of forged piping components such as flanges and forged fittings for small diameter pipes.

The specification is for pressure piping and fitting in the high or moderate temperature services.ASTM A234 (ASME SA234) pipe fittings after shaping from an elevated temperature, shall be cooled down to a temperature below critical range under suitable conditions which preventing injurious defects caused by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Referring standard in Section 7 of ASTM A960/A960M.

This material is durable, cost lower, and difficult to break. In case used in a stainless steel piping system it shall be adapted with a lap joint end ring.

Pipe fittings of ASTM A420 WPL6 are widely utilized in pressure piping and pressure vessel service at low-temperatures.ASTM A420 is the standard specification for pipe fittings of carbon steel and alloy steel used for low temperature services.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

HT PIPE is recognized as a manufacturer and exporter of A350 LF2 /LF3 Carbon Steel Flanges and Stainless Steel Flanges (Gr. 304, 304L, 316, 316L), available in many or grades, materials and finishes, in metric and imperial sizes .

We also accept all orders of CS Elbow A234 WPB up to and including 90 degree to suit your requirements.

There are seamless and welded A234 WP9 pipe fittings,the seamless A234 WP9 pipe fittings are manufactured from seamless steel pipes A335 P9,welded A234 WP9 pipe fittings mean they are made from welded pipes or steel plates.Studying the market demands, we deliver quality products that are sustainable. Our products are 100% certified.

ASTM A350 lf2 round bars are forged from standard quality carbon steel alloy. It has excellent tensile strength, corrosion resistance, ductility and mechanical properties that make it an excellent product. These carbon steel A350 LF2 bars are guaranteed to deliver the toughest industry standard products of the highest quality. Our CS A350 LF2 bars are made with the support of the latest equipment and are fully compliant with established industry specifications.

We are manufacturers, suppliers and exporters of Carbon Steel A105 / A105N Flanges, which, the American Society for testing materials, classifies as a standard that covers forged Carbon-Steel piping parts that also include carbon steel pipe flanges, which are serviceable in pressure systems at room temperatures as well as temperatures higher than it. We produce Carbon Steel A105 / A105N Blind Flanges which are successful in pressure bearing and sealing pipe ends in heavy pressure applications like hydraulic systems since they have a maximum bending stress at the centre.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

ASTM/ASME/ANSIB16.5, B16.47, ASME/ANSIB16.48 flange
Weld neck flange,WNRF Flange,Welding neck raise face flange,

Carbon steel forgings, manufactured in accordance with ASTM A105, are generally used for piping applications. These forged carbon steel piping components (including flanges, fittings, and valves, etc) are used for ambient- and higher-temperature service in pressure systems. The A105N, which is designated with a suffix ¡°N¡±, denotes that the A105 forging shall be furnished in normalized condition. If the forgings are used for piping applications of ASME BPVC or ASME B31, the material shall be its identical equivalent of SA-105 or SA-105N. In short, the heat treatment of normalization distinguishes A105N from A105, or SA-105N from SA-105. ASTM A105 Flange is a specification of flanges. The specification can include different grades of stainless steel material made flanges. The flanges are of forged carbon steel and are meant for high temperature services.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

These A234 WPB SCH 80 Elbow are also available in a wide size range. The purpose to use a ASTM A234 gr WPB elbow is to change direction or flow in a piping system.

Just as the corrosion resistance characteristics of carbon steel could be improved by further processing, it is possible to increase the mechanical properties of the ASTM A105 Fittings with the use of heat treatments.

a350 round bars are supplied in normalized, quenched and tempered, normalized and tempered conditions. a350 lf2 forged bar is a forged carbon/low alloy steel grade. It is primarily used for low temperature service and requires notch toughness testing. These carbon steel A350 LF2 bars are also made according to the changing needs of our esteemed customers. Additionally, our carbon steel round bar A350 LF2 is known for its toughness, robustness and cost-effectiveness.

RFWN Flanges (Raised Face Weld Neck Flange) are one of the most commonly used flanges in the piping industry. They are easy to recognize with their long tapered hub that is matched to the wall thickness (bore) of the pipe.

Carbon steel pipe flanges usually adopt mild steel or low carbon steel, as it includes small percentage of carbon, strong and tough but not readily tempered. Which with lower cost and material could be used for many applications.

Carbon steel LF3 round bars have the best corrosion resistance to general corrosion. Carbon steel LF3 threaded rods have good ductility and optimum creep properties. Carbon steel LF3 polishing rods have the best corrosion resistance to oxidation corrosion.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

The ASTM A420 Grade WPL6 can be seamless, welded or fabricated. There are different types of the fittings such as the unions, plugs, couplings, bends, caps and elbows.