ASTM A403 WP347H 180deg elbows steel pipe fitting fabrication

Steel pipes can be disintegrated on the basis of its application. Typical applications of steel pipes are in the area of water pipelines, industrial water lines, oil pipe lines, cross country pipe line, agriculture and irrigation pipes, tube lines for natural gas, chemical industries, automobile industry, construction industries and other purposes.

Stainless Steel 316 is an austenitic grade designed with excellent nickel and chromium content. This grade also contains a small amount of silicon, which improves the oxidation resistance of the module. In fact, stainless steel 1.4401 is often used in process streams containing halides such as chlorides because of its resistance to said compounds. The addition of molybdenum to stainless steel 316 tube alloys not only improves resistance to chloride pitting but also general corrosion.

Molybdenum-containing austenitic stainless steel DIN 1.4404 seamless pipe fittings are relatively low in carbon compared to DIN 1.4401 grades, but with small additions of molybdenum and nitrogen, and are used in light or moderately corrosive industries.

The resistance of the Monel 2.4360 eccentric/concentric reducer to salt solutions and its excellent resistance to stress-related corrosion cracking make the Monel 2.4360 eccentric/concentric reducer ideal for surviving in most freshwater bodies.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

The pitting resistance of ASME B16.9 SS 316L fittings is much higher compared to Grade 316. While Alloy 316L can be easily welded by most commonly used processes, Werkstoff Nr. is post weld heat treated.

The SS 316 fittings we sell are made of high quality materials that meet standards. Follow all sizes and dimensions so that our customers can trust our products. ANSI B16.9 Stainless Steel 316 Elbow Weight depends on the nominal size of the pipe, this standard ranges from ?” to 48″.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

For stainless steel sanitary fittings we offers a large selection of high purity food grade sanitary hose fittings, stainless sanitary tubing, sanitary valves and fittings, steel tubing clamps, etc. Contact us for a sanitary fittings price list.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

We hsve Elbow, ANSI B16.9 S32750 Welded Elbow, Super Duplex Steel S32750 Long Stub End, Super Duplex Steel S32750 Reducer Distributors, Super Duplex S32750 Concentric Reducer, Super Duplex Steel DIN 1.4410 Tees, SAF 2507 Super Duplex Steel Long Radius Bend, Super Duplex Steel S32750 90 deg. Elbow, Super Duplex S32750 180 Deg. Buttweld Elbow, Super Duplex S32750 180 Deg. Buttweld Elbow, ASME SA815 S32750 90 deg Elbow Suppliers, Super Duplex Stainless Steel S32750 Seamless Pipe Elbow, Super Duplex 2507 Eccentric Reducer, UNS S32750 Pipe Fittings, S32750 Pipe Fittings Stockist, Super Duplex Steel 1.4410 Short Stub End, ANSI B16.9 S32750 Super Duplex Steel Stubends.

Stainless steel 316L fittings are one such product, made from grade 316 with a lower carbon content. Low carbon is indicated by the suffix letter “L”. They show higher resistance to oxidation and corrosion.

317L is non-magnetic in the annealed condition but may become slightly magnetic as a result of welding.Fittings supplied under this specification shall be examined visually for surface discontinuities, surface checks, and mechanical marks.

ASTM A234 includes both seamless and welded pipe fittings, seamless steel pipe fittings refer to pipe fitting raw materials made from seamless steel pipes and pipes; therefore, welded steel pipe fittings cover fitting raw materials from welded steel pipes.

A sanitary elbow is a kind of sanitary fitting installed between two lengths of pipe or tubing to allow a change of direction. While these corner fittings are usually a 90¡ã or 45¡ã angle, 22.5¡ã elbows are also available.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Hastelloy C-22 is identified by the Unified Numbering System (UNS) designation of?N06022. It is a nickel based alloy with high nickel (56%), chromium (22%), and molyddenum (13%).

INCOLOY Alloy 800 (UNS N08800/W. Nr. 1.4876) is a widely used material for the manufacture of equipment requiring corrosion resistance, heat resistance, strength and stability, operating temperatures up to 1500¡ãF (816¡ãC) ).

Our SS 310S pipe fittings are made of low carbon austenitic steel known for its ability to resist corrosion, especially water corrosion and sulfidation in chemical and ore processing units.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Stainless steel 316L fittings are made from a low carbon version of the 316 material. Elbows also have different variations. The usual elbow is a 90 degree elbow, with 45 degree elbows and short and long radius versions also available.

These stainless steel pipe fittings have excellent corrosion resistance and dimensional accuracy along with close tolerances. Our range of pipe fittings include butt weld pipe fitting & instrumentation and ferrule fitting are offered in different sizes, we also provide customization as per the requirements of clients.

The combined effects of mechanical and thermal processing of Incoloy Alloy 800HT permit higher design stresses to be incorporated than are permitted for the conventional Alloy 800H.

Our Duplex Steel S31803, S32205 Seamless Pipe Fittings are machinable and weldable and ductile even at low temperatures. Duplex steel UNS S31803 butt welded pipe fittings generally have excellent corrosion resistance compared to other austenitic steels.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

ASTM A234 is Standard Specification for steel pipe fittings includes carbon and alloy steel material for moderate and high temperature services.

WPHY 52 Fittings are recommended be heat treated by one or more of the following procedures: annealing (stress relieving), normalizing, normalizing and tempering, quenching and tempering.Made utilizing high-grade crude materials, these ASTM A860 WPHY Pipe Fittings are anti-corrosive and strong.

It is more resistant to general corrosion and pitting than conventional nickel chromium stainless steels such as 302-304.