nickel alloy monel 400 bar 50mm dia rod

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

The Alloy K500 Studs are threaded rods with threads on both ends. They can be different types depending on the threaded distance from the center and the thread type. The material is high temperature and high pressure resistant. It has 1350 degrees Celsius melting point, 790MPa minimum yield strength and 1100MPa minimum tensile strength. These values are double the strength of 304 grade.

Monel K500 pipe bend and elbow are usually used in propeller, pump shafts, pumps, valves used in the manufacture of perchlorethylene, and chlorinated plastics.

ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. ASTM B 564 Monel K500 Lap Joint Flanges may be used at all pressures and are available in a full- size range. They can be salvaged for use in systems that erode or corrode quickly. We keep a tab on market trends and demands, to invent new, sustainable and economical products capable of undergoing customization. Our products are fully certified and 100% durable.

Reworking of Alloy K-500 is best done while the material is in the annealed or hot worked and quenched condition. However, age hardened materials can be finished to close tolerances and finish. Therefore, the recommended practice is to machine slightly oversize, age harden, and then finish to size.

The alloy can be machined at satisfactory speeds with machine tools commonly used in the industry. Generally, cold drawn or cold drawn stress relief materials are recommended for the best machinability and smoothest finish.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

A nyloc nut, also referred to as a nylon-insert lock nut, polymer-insert lock nut, or elastic stop nut, is a kind of locknut with a nylon collar that increases friction on the screw thread.

A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel 400 provide superior quality for different types of mechanical, and general engineering applications.

Unique among Monel alloys, ASTM B165 Monel Seamless and Welded Pipe is considered a Puritan alloy because it contains the same nickel and copper content as the natural nickel ore found in the Sudbury mine in Ontario, Canada.

Nimonic 80 a (Alloy 80A) is one of the most popular superalloys specified for gas turbines. Nimonic 80A fasteners are often specified because of their ability to withstand very high temperatures. This makes Nimonic bolts and nuts ideal for use in aircraft parts and custom-designed gas turbine components, from turbine blade mounting to exhaust nozzles on jet engines, where Nimonic fasteners are exposed to very high levels of pressure and heat.

Alloy 400 exhibits corrosion resistance to many reducing media.

The deformation activation energy is low during superplastic deformation, and the process may be controlled by diffusion.

The corrosion resistance of Monel alloy K-500 is subtantially equivalent to that of alloy 400 except that, when in the age-hardened condition, alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

INCOLOY alloys belong to the category of super austenitic stainless steels. These alloys have nickel-chromium-iron as the base metals, with additives such as molybdenum, copper, nitrogen and silicon. These alloys are known for their excellent strength at elevated temperatures and good corrosion resistance in a variety of corrosive environments.
The Alloy 800 Elbow is widely used in various industries and is primarily famous for its excellent mechanical properties. The Werkstoff Nr. 1.4876 End Cap has low gas content, low vapor pressure, and high thermo-electric conductivity.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

Monel 400 flanges are also available for higher temperatures in reduction environments. While Monel 400 flanges are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 flanges.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Monel 400 is a popular, high performance nickel-copper alloy commonly used in critical and high performance applications.

It is not useful in oxidizing acids, such as nitric acid and nitrous.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Chromium in Monel K500 Spectacle Blind Flanges gives resistance to oxidizing conditions, such as nitric acid solutions, nitrates and oxidizing salts.

The blind flanges are used to close a connection while the slip on flanges are used to adjust a connection position. The ASTM B564 Monel 400 Slip On Flanges allow the seamless pipes to slip onto them so the positioning becomes easy. There are welded flanges as well as threaded flanges.

The corrosion resistance of Monel K-500 is basically the same as Alloy 400, except that in the age hardened condition, Alloy K-500 has a greater tendency to stress corrosion cracking in certain environments. Monel K-500 has been found to be resistant to sour gas environments.

Monel 400 contains the same levels of nickel and copper as the natural nickel ore found.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.

Alloy 400 Seamless Pipe exhibits excellent resistance to not only caustic solutions but also brine and seawater, which makes it perfect for marine applications.

MONEL K500 es una aleacion de niquel-cobre que se puede endurecer por precipitacion mediante la adicion de aluminio y titanio.