Monel K500 Flanges offer outstanding low temperature properties

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

The Alloy 400 Slip-on Flange is often seen in the marine industry as the alloy exhibits have good resistance to not only seawater but also to high velocity brackish water.

Monel 400 Bolt is a nickel-copper alloy, a solid solution nickel alloy that can only be hardened by cold work. Known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher than copper alloys in oxidizing environments. Monel 400 bolts, also known as Alloy 400, are also used in high temperature, caustic and salt solution applications.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

One of the most important characteristics of Monel 400 is that stress corrosion cracks do not occur in general, and the cutting performance is good. The structure of Monel 400 is single phase solid solution with high strength.

Alloy 400 is virtually immune to chloride stress corrosion cracking in typical environments. Generally, its corrosion resistance is good in reducing environment, but poor in oxidizing environment.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel K500 pipe bend and elbow has excellent mechanical properties from sub-zero temperatures up to about 480C.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

But since the chief alloyant in the ASTM B564 UNS N04400 SORF Flange is nickel, the resistance to these particular reductive solutions is strong.

Monel k500 round bar is an age hardening nickel base alloy. This nickel-based Monel UNS No5500 triangular bar also contains some elemental copper added to its alloy. Copper is known to have good corrosion resistance when added to Monel UNS 5500 spring steel bar, similar to alloy grade 400.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Monel 400 Tee is a nickel-copper alloy resistant to seawater and steam at high temperatures, as well as salts and corrosive solutions. Monel 400 Pipe Elbows operate over a wide temperature range and are available in a variety of styles for a variety of products.

A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance to a wide range of media.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

The strength of this nickel steel alloy is maintained to 1200¡ã F but stays ductile and tough down to temperatures of 400¡ã F. Its melting range is 2400-2460¡ã F.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

It is not useful in oxidizing acids, such as nitric acid and nitrous.

Over and above the nickel copper base, elements like aluminium and titanium in the chemistry of the Monel K500 Lap Joint Flange proves to be very fruitful. In fact, this modified chemistry along with the heat treatment that is given to the alloy under controlled conditions ensures that the particles of both Ti and Al have been precipitated in the matrix of Monel K500.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC).

Reworking of Alloy K-500 is best done while the material is in the annealed or hot worked and quenched condition. However, age hardened materials can be finished to close tolerances and finish. Therefore, the recommended practice is to machine slightly oversize, age harden, and then finish to size.

Inconel alloy is a family of nickel-chromium superalloys and a trademark of Special Metals Corporation. Inconel 601 is resistant to high-temperature oxidation. The alloy also has good resistance to aqueous corrosion, has high mechanical strength, and is readily formed, machined, and welded.

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness.

This alloy is not suitable for highly oxidizing acids such as nitric acid and nitrous acid. It is resistant to sulfuric acid up to 80% and hydrochloric acid solutions up to 20%.

This alloy is more resistant to nickel under reducing conditions and more resistant than copper under oxidizing conditions, it does show however better resistance to reducing media than oxidizing.

The Stud Bolt is a threaded rod with 2 heavy hexagon nuts, while the Hex Bolt has a head with one nut. Nuts and head are both six sided. Bolts threading are defined in ASME B1.1 Unified Inch Screw Threads, (UN and UNR Thread Form). The most common thread is a symmetrical form with a V-profile. The included angle is 60¡ã. This form is widely used in the Unified thread (UN, UNC, UNF, UNRC, UNRF) form as the ISO / metric threads.

The deformation activation energy is low during superplastic deformation, and the process may be controlled by diffusion.

Monel 400 operates in a wide range of acidic and alkaline environments and has excellent ductility and thermal conductivity. Its properties make it ideal for heavy-duty applications and those requiring a high melting point and toughness in the harshest conditions.