pipe fitting

We manufacture SA403 WP 304 Short Radius and Long Radius Elbows very strong with a minimum yield strength of 205MPa and a minimum tensile strength of 515MPa. These work well in high temperature environments up to 870 degrees Celsius.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.

ASTM A403/ A182/ A240 and ANSI B16.9/16.28/ B16.25/ MSS SP-43. 316/316L is a nickel-chromium stainless steel alloy to which copper and molybdenum have been added. It is a non-magnetic austenitic stainless steel, so it is especially useful in severely corrosive conditions.

Copper-nickel is known for its broad resistance to seawater. Due to the high absorption rate of the alloy, copper-nickel (Cu-Ni) 70/30, (Cu-Ni) 90/10 pipe fittings are widely used as connectors for piping systems in the power generation and shipbuilding industries.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Usually the ASTM A234 WP9 elbows,tees,reducers are made from steel pipes,the caps are made from plates.But the large sizes pipe fittings are commonly manufactured in pieces and welded together.In hot or concentrated solutions, rates of these Alloy Steel WP9 Cross Butt Weld Fittings are typically too high for sensible service life.

Duplex fittings are used in different types of piping applications. 2205 is a standard duplex steel with 21% chromium. The material is strong, twice as strong as austenitic steel types. Different standards such as ASME B16.9, B16.28 and B16.25 govern the dimensions. Depending on the type of fitting, the nominal bore diameter of the fitting can also vary.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

Super duplex 2507 / UNS S32750 pipe fittings have great resistive properties to chloride stress corrosion cracking and a high thermal conductivity with a low coefficient of thermal expansion. These pipe fittings have a great resistance to inorganic acids used in dilute hydrochloric acid.

Duplex steel UNS S32205 butt welded pipe fittings are available in a variety of styles such as elbows, elbows, equal and unequal (reducing) tees, equal and reducing (reducing) crosses, concentric and eccentric Reducers, end caps, long and short pipes, seamless butt welded pipe fittings, welded butt welded pipe fittings, etc. Also known as WNR 1.4462 pipe fittings, our duplex steels can be further customized in thickness, size and specification according to the precise requirements of our valuable customers.

Alloy 400 is resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

SA403 wp304 pipe end caps cover pipe ends, stop fluid flow and protect pipe threads. In multi-end fittings, it is often used to direct flow to a specific end.

This fitting is used in piping systems to change direction or function and is mechanically connected to the system. The easiest way to do this is to bend the pipe in the desired direction, but this process will stretch and thin the outer wall of the pipe while thickening and wrinkling the inner wall of the pipe. Our 2205 line of duplex fittings includes long radius elbows and short radius elbows.

The Incoloy 825 consists of small amounts of copper, titanium, and molybdenum, contributing to its excellent mechanical properties. The Incoloy 825 Pipe Fittings have high resistance to pitting and crevice corrosion.

A reputed distributor and supplier of Duplex S31803 Fittings, the most widely used duplex (ferritic/austenitic) stainless steel grade. We recognize the importance of supplying raw and pre-machined duplex UNS S31803 welded butt welded pipe fittings that are trusted for quality, mill source traceability, supply accuracy and fast delivery. Duplex UNS S31803 Elbow Fittings are extremely corrosion resistant and work hardenable alloys.

Grade 2205 is the most widely used duplex stainless steel grade. Fittings of this grade finds applications due to both their excellent corrosion resistance as well as their high strength.

Corrosion resistance of duplex steel radius fittings provided. Comparable to standard austenitic grades or high alloyed ferrites. While duplex steels have good high temperature oxidation resistance like other duplex stainless steels, embrittlement can occur even at temperatures above 300 degrees Celsius for short periods of time. In case of embrittlement, duplex steel stub joints can only be corrected by a complete solution annealing treatment.

B16.11 Forged Fittings, Socket-Welding and Threaded ASTM B366 specification covers Inconel, Monel, Hastelloy and Nickel Alloy Pipe Fittings used in acidic and sea water.

The Stainless Steel Fittings Manufacturers produce these fittings with the addition of manganese, phosphorus, carbon, silicon, and sulfur apart from the 2 main elements.

Inconel 600 fittings are made from a nickel-chromium alloy that contains a minimum of 72% nickel and 14% chromium in a composition with carbon, manganese, silicon, sulfur, copper and iron.

Monel 400? can be used in temperatures up to 1000 oF. Monel K-500 is basically a better version of 400 and has higher strength and hardness.

ASME SA 240 UNS S32205 elbows are standard elbows that can be connected to almost any size elbow. These elbows are available in NPS ? to NPS 48 and can change the direction of flow in the pipe. UNS S32205 elbows are stronger than austenitic stainless steels.

ASTM A403 WP347H ismainly used where corrosion resistance and sustained operations at temperatures between 800¡ã F. and 1600¡ã F. is of the utmost importance. It is also a superior grade for use on heavy welded objects, which cannot be re-annealed.

The molybdenum content increases corrosion resistance, improves resistance to pitting in chloride ion solutions, and increases strength at high temperatures.

Incoloy 800 pipe fittings, resistant to seawater and salt water even in reducing environments.

Butt welded pipe fittings provide the user with a means of manipulating the piping system. For example, elbow stainless steel pipe fittings can be produced at customizable angles if the system needs to change the flow direction.

It can be easily formed. Our duplex steel fittings are austenitic-ferritic stainless steels for corrosive environments that resist localized corrosion such as pitting, crevice corrosion and stress corrosion cracking.

Therefore, stainless steel elbows are widely used in high temperature applications. A403 WP316 elbows are widely used to change the direction of pipes and are available in different diameters, shapes and sizes. A403 WP304 elbows can be easily welded, but the material may face localized corrosion due to the risk of intergranular corrosion.