steel bar titanium round bar A182 F22 steel bar

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Alloy Steel Flanges are made in different steel alloys. The flanges vary in dimensions and types. There are ? inches through 48 inches of nominal diameter sizes of flanges.

The A320 Gr L7 stud material will undergo the following parametric tests – Impact Test, Tensile Test and Hardness Test according to the mechanical specification of A320 Grade L7 Bolts. The specification of A320 Gr L7 Hdg covers several grades of stainless steel including austenitic and ferritic stainless steels.

ASTM A335 P91 grade pipe is a high quality pipe for high pressure boilers. P91 tubing is ideal for bending, flanging or for welding and similar operations. The material of steel should adhere to the requirements of chemical composition, tensile properties and hardness.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P113

Nuts with a nominal size over 1 inch shall be a UNC Series Class 2B fit or an 8 UN Series Class 2B fit. High strength ASTM A194 grade 2H nuts are common in the market and are often replaced by ASTM A563 grade DH nuts due to the limited availability of DH nuts in certain diameters and finishes.

The wider range of flanges are being offered like ASTM A182 F9 slip flange, F9 alloy welded steel socket flange, alloy steel F9 orifice flange, A182 F9 threaded and screwed flange etc. Imperative for the uniqueness of Alloy Steel F9 Socket Weld Flanges is the allotropy of iron-that is, its existence in two crystalline structures.

Grade B7 is a heat-treated chromium-molybdenum low-alloy steel with minimum tensile strength requirement of 125 ksi (860 Mpa), yield 105 ksi (720 Mpa), and maximum hardness of 35HRC.

A193 B7 threaded rods are also known as hex bolts. It has threads on both ends and it is a relatively long rod.

Flange is usually used for connecting pipes or valves, so it can solve the above problems easily.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

When the F11 flange is heat treated, the alloy steel F22 flange is formed. These flanges have a tensile strength of 655 MPa and a yield strength of 517 MPa.

In order to strengthen chromium alloy flanges, elements such as copper, titanium, vanadium and niobium are added to the alloy.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

ASME SA182 F5 pipe flange weight depends on wall thickness and nominal bore. The wall thickness of the flange is determined by the pressure rating.

A182-F11 has high thermal strength (¦Äb¡Ý440MPa) and oxidation resistance at high temperature, and has certain resistance to hydrogen corrosion.

ASTM A194 Grade 2H bolts are high strength bolts made from carbon steel.

It can be used with other a335 gr P22 alloy tube types and fittings. SA 335 gr P22 alloy steel pipe has high heat resistance and low thermal expansion. This property of P22 metal tubing makes it suitable for use in the oil and gas industry, power industry, petrochemical industry and refineries where temperatures often fluctuate at high temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.44

The high chromium content gives these forgings fittings very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

Pipe to ASTM A335 P11 can be cold drawn or hot rolled. Each tube shall be reheated for heat treatment – fully or isothermally annealed, normalized and tempered at a temperature not lower than 1200¡ãF (650¡ãC). Each pipe length shall be hydrostatically tested to ASTM A335 P11, along with dimensional inspection and visual inspection. Longitudinal or transverse tensile tests, flattening tests or bending tests are carried out for each heat.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P129

Production of low alloy steel materials of different specifications. A335 is a specification for seamless ferritic alloy steel pipes. These alloy steel seamless pipes are used for high temperature service. There are also high alloy steel materials. There are different grades in this material specification. There are grades P1, P2 to P91 and P92. The most commonly used grades are p5, p9, p11, p22, p91 and p91.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P136

ASTM A335 P9 pipe standards and schedules vary based on the needs of the application. A335 P9 chromium pipe composition contains 9% chromium and 1% molybdenum.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.55

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A182 Stainless Steel Flanges are manufactured per ASME B16.5 150#, 300#, 600#, 900#, 1500#, 2500#.

Although blind flanges and certain reducing flanges could include plate as a material for construction.

ASTM A193 Grade B7 specification covers requirements for high tensile alloy steel bolting material for use in high temperature or high-pressure service and other special purpose applications.

While each variation of Inconel has unique traits that make it effective in different circumstances, the majority of the alloys are used frequently in the chemical industry.Its welding characteristics,
especially its resistance to postweld cracking, are
outstanding

SA182 F5 Plate Flange can be used in those environments where there is a presence of mild corrosive compounds. It can also be used in non-corrosive applications as well as in erosive applications at the temperature between ranging between -30oC up to +650oC. ASTM A182 Grade F5 Flanges in conditions characterized by increased levels of carbon dioxide (CO2), hydrogen sulphide (H2S), and as well chlorides (Cl). The highlight of A182 F5 Steel Slip On Flanges are Precise plan, Accurate measurements, Resistant to corrosion, Less costs, pitting and crevice resistance.