4140 steel round bar sizes alloy bar

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

The high chromium content gives these forgings fittings very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

All chrome molybdenum steel sheets are sedated and heat treated in accordance with ASTM A387, which also specifies minimum and maximum levels of the following elements in steel: Chemicals of Carbon, Manganese, Phosphorus, Sulfur, Silicon, Chromium, Molybdenum, Nickel, Vanadium requirements, columbium, boron, nitrogen, aluminum, titanium and zirconium. A387 boards must undergo product, chemical and tensile testing (documented in the MTC or material test certificate) – must meet specific requirements for tensile strength, yield strength and elongation.

The a182 f9 material contains a certain amount of chromium and molybdenum, both of which contribute to a longer service life and therefore longer life.

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel flanges, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

ASTM A182 Low Alloy Steel flanges as well as the other types of alloys. The ASTM A 182 specification specifies flanges for high pressure services.

Alloy Steel Flanges, Alloy Flanges are carefully designed using current technology under the visionary guidance of accomplished professionals in the manufacturing sector.

ASME SA182 F5 pipe flange weight depends on wall thickness and nominal bore. The wall thickness of the flange is determined by the pressure rating.

ASTM A193 Grade B8M Grade 1 Fasteners are similar to Grade B8 but are made of AISI 316 stainless steel instead of AISI 304 stainless steel. Type 316 stainless steel has better corrosion resistance than type 304 stainless steel due to the addition of molybdenum.

P11 Pipe is a chromium molybdenum alloy made pipe. It is used in the high temperature services. It is corrosion resistant, strong and ductile. Steel India Company is a manufacturer of different grades of the chromium molybdenum alloy made pipes.

Nuts with a nominal size over 1 inch shall be a UNC Series Class 2B fit or an 8 UN Series Class 2B fit. High strength ASTM A194 grade 2H nuts are common in the market and are often replaced by ASTM A563 grade DH nuts due to the limited availability of DH nuts in certain diameters and finishes.

Alloy Steel F12 slip on Flanges are made up of chromium molybdenum steel alloy and therefore have a high rupture resistance. They are also preferred due to their light weight because of the low carbon and high alloy nature.Alloy Steel ASTM A182 flanges are very simple to install and have a low center because the pipe occasionally trips into the flanges after welding.

ASTM A182 F91 is an American standard Martensite type heat-resistant steel forgings, according to ASTM A182-2016.

The main components of ASTM A335 grade P91 are also molybdenum (Moly) and chromium (Chrome). These elements provide pipes with specific properties such as enhanced corrosion resistance and increased overall strength, creep resistance and wear resistance.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.29

ASTM A182 is the Standard Specification for Forged Stainless Steel Pipe Flanges and Stainless Steel Forged Fittings.

ASTM A335 P22 pipe specifications include seamless “chrome molybdenum” alloy steel pipe and alloy steel pipe. Chromium is an important compound in stainless steel. Any steel with 12% or more chromium is considered stainless steel. Unrivaled chromium resists oxidation at high temperatures.

Our ASTM A182 F5 Alloy Steel Blind Flanges are square and can be used to connect pipes of nominal bore size without welding and are suitable for high pressure hydraulic systems.

The material contains carbon, manganese, phosphorus, sulfur, silicon, 8% chromium and molybdenum in a mixture. SA 335 grade P5 alloy steel pipe has similar strength to most austenitic stainless steel grades, with a minimum yield strength of 205MPa and a minimum tensile strength of 415MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P120

Schedules vary based on nominal bore diameter in relation to wall thickness. Schedules range from sch20 to XXS. Pipe lengths up to 13500 mm. There are seamless pipes and fabricated pipes in this specification. ASTM A335 P5 pipe can be round, hydraulic, rectangular, square or hexagonal. The length of the pipe can also be cut to length size according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P148

ASME SA 335 P91 Alloy Steel Pipe also has some other great features like low maintenance, efficient work, high demands, etc. We offer a range of ASTM A335 P91 alloy steel pipes for a wide range of applications in various industries.

Weld Neck Flange is flanges that designed to be joined to a piping system by butt welding. This kind of flange include lots of specification.

One of the top stocks of ASTM A182 alloy steel F5 flanges for a variety of industrial applications. With a talented team of professionals, we are committed to supplying the highest quality ASTM A182 Alloy Steel F5 Flanges, widely used by customers in suitable applications.

Chrome moly flanges provide improved levels of chromium and molybdenum. The addition of chromium helps to increase itshardenability and corrosion resistance,

The addition of molybdenum strengthens the elastic limit of the A335 p11 welded pipe and increases its temperature strength. In addition to these properties, there is a reduction in brittleness and an improvement in the weldability and hardenability of the pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.48

The specification for standard ASTM A182 F9 Flanges covers both forged or Rolled Alloy Steel Pipe Flanges & Fittings, that have been designed and manufactured for high temperature service. ASTM A182 F9 Flanges have a minimum chromium content of 18% in the alloy. This makes it survive in temperatures up to 870 degrees Celsius.

While each variation of Inconel has unique traits that make it effective in different circumstances, the majority of the alloys are used frequently in the chemical industry.Its welding characteristics,
especially its resistance to postweld cracking, are
outstanding

These supplied alloy steel F2 A182 bars are manufactured synchronously through set industry specifications using high quality raw materials and leading technology. Regarding the domestic and international quality of the raw materials, we also offer these round bars and bars in custom sizes.

While the term alloy steel could even apply to stainless steel grades, the ASTM specification or ANSI standard used to produce the Alloy Steel Flanges would give the buyer details regarding the chemistry details of these products.

These well-controlled advantages of Astm a182 alloy steel F9 round bars are evident in automated operations where even modest changes in flow temperature can significantly increase the incidence of scrap.

B8M Grade 1 fasteners require carbide solution treatment, while Grade 2 fasteners require additional strain hardening operations to increase strength and reduce susceptibility to wear.

Based on our research and understanding of ongoing trends, we adjust our production and delivery patterns to offer our customers unique and portable products.