ASTM A182 F5 F9 F11 F12 F22 F91 Flanges for nuclear power petrochemicals and acidic

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Imperative for the uniqueness of Alloy Steel F9 Socket Weld Flanges is the allotropy of iron-that is, its existence in two crystalline structures. Alloy Steel(AS) F9 Long Weld Neck Flanges can be carbide of an alloying element such as titanium.

WPHY 52 Fittings are recommended be heat treated by one or more of the following procedures: annealing (stress relieving), normalizing, normalizing and tempering, quenching and tempering.Made utilizing high-grade crude materials, these ASTM A860 WPHY Pipe Fittings are anti-corrosive and strong.

ASTM A182 F11 Alloy Steel Flanges are used in manufacturing of flanges and fittings and are used in industries where cold temperature is observed and corrosion resistance doesn¡¯t matter much.

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel flanges, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

These are used in applications where the resistance required is not much and general corrosion resistance is required.

A182 pipe flanges tend to have fairly high electrical conductivity among other wrought alloy steels in their class. It has a higher base cost and higher embodied energy.

Alloy 32750 is a super duplex stainless steel supplied in hot worked and solution annealed conditions. As a super duplex stainless steel, it combines the desirable aspects of austenitic and ferritic steels. Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature over 50¡ãC.

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.

For A335 steel pipe, the addition of molybdenum (“Moly”) increases the strength and elastic limit of the steel, and enhances the wear resistance, impact quality and hardenability of the steel. It also improves softening resistance, makes chrome steel less brittle and prevents pitting corrosion. Chromium is also a key element in stainless steel alloys, preventing oxidation of the steel at high temperatures and improving the corrosion resistance of the steel. It improves the tensile, yield and hardness properties of low alloy pipes at room temperature.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P104

The Alloy Steel Blind Flanges are used to close a pipe connection. There are different types and grades of the blind flanges as well.

The size of these forgings range from ? NB to 250 NB and length of these forgings is 2mm to 40mm.

ASTM A182 F12 round bar is commonly used in different industries, such as air-conditioning industry, aluminum industry, boiler industry, steel industry, cement industry, construction industry, etc. ASME SA 182 F12 bar stock is available in a variety of sizes to meet different customer requirements.

Hot rolled 4140 steel also has good fatigue resistance and impact resistance after heat treatment.

Grade B7 is a heat-treated chromium-molybdenum alloy steel with minimum tensile requirement of 100 ksi, yield of 75 ksi and maximum hardness of 35 HRC.

Bolts are chrome molybdenum heat treated steel according to ASTM A193 B7m specification for bolts. The primary alloy components of ASTM A193 Grade B7 bolts are chromium and molybdenum. These ASTM A193 B7 Metric Bolts are manufactured by heat quenching and tempering. Heat treating A193 B7 bolt material helps to develop desired mechanical properties such as increased tensile strength of ASTM A193 B7 hex bolts after heat treatment.

Grade B7 is a heat treated chromium molybdenum low alloy steel with a minimum tensile strength requirement of 125 ksi (860 Mpa), a yield strength of 105 ksi (720 Mpa) and a maximum hardness of 35HRC. Boltport produces B7 headed and headless bolts from alloy steel AISI 4140 bar stock or forgings. A193 Grade B7 is the most commonly used bolting size, plus A194 Grade 2H nuts are used for bolting carbon steel pipe. A193 B7 bolts are available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches in diameter.

Blind flanges have the face thickness of a flange, a matching face type, and similar bolting pattern.

The connection between two pipes can be directly welded together, but it is difficult to connect together without welding. When the connection part have problems, it will be hard to repair. The same problem also happened between pipe and valve connection.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

The weld neck flange comprises of a round fitting that extends beyond the rim of the circumference. These flanges, typically manufactured from forging, are actually welded to pipes.

We are a professional manufacturer and exporter of ASTM B366 WP20CB Pipe Fittings N08020 elbow, Alloy 20 Elbow Tee reducer Caps

It exhibits exceptional corrosion resistance in chemical environments containing phosphoric acid, nitric acid, chlorides and sulfuric acid. It also has good mechanical properties at both ambient and elevated temperatures.

The addition of elements such as silicon and manganese through heat treatment provides alloyed steel with improved properties and additional benefits, such as increased corrosion resistance or increased reliability. Alloy steels are also found in applications where their response to magnetism is important, such as in transformers and electric motors.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

These pipe fittings of B366 N06601 B366 N08825 B366 N10276 B366 N08020 materials, are used in the chemical industry, as well as in pressure vessels.

The Alloy Steel F12 Flanges are also very strong due to the annealing of them. Grade F12 Flanges can be supplied in either normalized or quenched and tempered conditions. Alloy Steel F12 Weld Neck Flanges is appropriate to various applications where its different remarkable characteristics are sought-after but a brushed/polished finish is not necessary.

The alloy content of pipes that make up low alloy steel is less than 5%. High alloy steels, on the other hand, have an alloy content ranging from 5% to about 50%. Similar to most alloys, the working pressure capacity of alloy steel seamless pipe is about 20% higher than that of welded pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P127

ASTM A182 Alloy Steel Forged Fittings are manufactured according to the ASTM A182 specification, which covers high pressure and high temperature service flanges covered by ASME B16.11, MSS-SP-79/ 83/ 95/ 97 and BS3799 standards.

Nickel alloy 20 is a low-carbon, niobium-stabilized austenitic nickel/iron/chromium alloy with additions of molybdenum and copper. ASTM B366 specification covers Inconel, Monel, Hastelloy and Nickel Alloy Pipe Fittings used in acidic and sea water.