Monel 400 2.4360 nickel alloy pipe prefabrication resistant to steam at high temperatures

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

The deformation activation energy is low during superplastic deformation, and the process may be controlled by diffusion.

Monel bolts, like Monel 400 and K500, are made from a nickel-copper alloy and exhibit high strength, toughness and good corrosion resistance over a wide temperature range.

Overcoming the impact of downtime caused by corrosion, stress and extreme temperatures, and the cost impact of failure rates and safety has driven the industry to look for materials like Monel 400, which provide increased reliability in harsh conditions.

This nickel alloy has good corrosion resistance, good wear resistance and high strength.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

In applications that involve being used at subzero temperature, the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance

There are different pressure classes of these flanges ranging from Class 150 Monel UNS N04400 Flanges to class 2500, and PN6 to PN64.

Monel400 is a single-phase solid solution Ni-Cu corrosion-resistant alloy.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Chromium in Monel K500 Spectacle Blind Flanges gives resistance to oxidizing conditions, such as nitric acid solutions, nitrates and oxidizing salts.

In addition to high ductility, the material shares several other characteristics with nickel. For example, ASTM B164 Monel 400 round bar is well suited to work in moderately reducing applications because nickel works very well in reducing environments.

UNS N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

MONEL? alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy which combines the excellent corrosion resistance of MONEL alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

Monel 400 is well known for its high strength and corrosion resistant properties. It works in a wide range of temperatures, and is available in multiple forms for a variety of products. Monel 400 is used extensively in (for pipe) piping. Resistant to both steam and seawater, its toughness and anti-corrosive properties make it perfect for heavy duty applications such as transfer (pipe) piping used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Unique among Monel alloys, ASTM B165 Monel Seamless and Welded Pipe is considered a Puritan alloy because it contains the same nickel and copper content as the natural nickel ore found in the Sudbury mine in Ontario, Canada.

While it is a very useful metal, it is cost prohibitive in most applications. Monel 400 costs 5 to 10 times as much as regular nickel or copper.

A nyloc nut, also referred to as a nylon-insert lock nut, polymer-insert lock nut, or elastic stop nut, is a kind of locknut with a nylon collar that increases friction on the screw thread.

The Alloy K500 Pipe Flanges have 63% nickel with 28% copper and carbon, manganese, silicon, sulfur and iron. The iron component in the monel K500 is much lower than that of monel 400. The Monel UNS N04400 Flanges also come under different standards such as ASTM, ASME, ANSI, DIN and all other international standards with varying dimensions. The dimensions of the flanges determine the pressure classes.

Generally, its corrosion resistance is very good in reducing environments, but poor in oxidizing conditions.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Common trade names include alloy 400, UNS N04400, Monel alloy. Monel? is a registered tradename of Special Metals Corporation.

Also known as alloy K500, Monel K500 bolts are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

MONEL K500 retains the excellent corrosion resistant characteristics of 400 and has enhanced strength and hardness after precipitation hardening when compared with 400.

Monel K500 Fasteners are thermally applied or manipulated to affect precipitation. This process is called age hardening. These fasteners have a greater tendency to stress corrosion cracking in a variety of harsh environments when exposed to the age hardening process. It has three times the yield strength compared to the standard version. Monel 500 material is an age-hardenable nickel-copper alloy that combines the corrosion resistance of Alloy 400 with the high strength corrosion fatigue and erosion resistance.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.