Monel K500 tube and pipe low corrosion rates in high-velocity sea water

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Alloy 400 is highly regarded as one of the best performing engineering alloys.

Preferred by many a Monel Flanges Manufacturer In India, this alloy exhibits high tensile strength making it a commercially viable option for marine engineering purposes. The Wnr 2.4360 Reducing Flange is resistant to chloride stress corrosion cracking, which is a common issue in marine environments.

The Asme B16.5 Inconel 600 Flange exhibits good resistance across a broad range of corrosive mediums. The chromium content in the Alloy 600 Flanges gives them better resistance as compared to both Alloy 200 as well as alloy 201 under oxidizing conditions. Also, These Monel K500 Flanges are technologically advanced under the direction of skilled specialists by making use of the premium quality of materials.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Monel 400 (UNS N04400) is a nickel-copper alloy with optimum high strength and corrosion resistance. It is widely used in a variety of severe acidic and alkaline environments. Monel is also used in pipes.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance to a wide range of media.

Astm B564 Monel 400 Blind Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Las aplicaciones tipicas de la alta resistencia y resistencia a la corrosion de MONEL K500 son ejes de bombas, impulsores, ejes de helices, componentes de valvulas para barcos y torres de perforacion en alta mar, pernos, collares de pozos de petroleo y componentes de instrumentacion para la produccion de petroleo y gas.

Class 150 Uns N05500 Socket Weld Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

We are Manufacturers, Supplier and Exporters of Monel K500 Flanges. These Monel R405 flanges are used with stub end or daft which is butt welded to the pipe with the flange loose behind it.

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Nickel 400 Annealed Pipe, which is also referred to as a superalloy can be annealed at a temperature of 926¡ãC.

MONEL K500 retains the excellent corrosion resistant characteristics of 400 and has enhanced strength and hardness after precipitation hardening when compared with 400.

MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium.

The Curie temperature of this alloy lies within the ambient temperature range and is affected by changes in the alloy’s chemical composition. Caution is recommended in applications requiring strong non-magnetic properties.

Monel 400 Socket Weld Flanges have good weldability and moderate resistance to corrosive environments. Nickel 400 glasses blind flanges for terminating pipes or pipes are resistant to seawater and steam at high temperatures.

Yet some alloys like the Monel 400 Flanges can perform well in marine environments because of their chemical composition. With the content of copper ranging between 28% to 34%, it is referred to as a superalloy for its good corrosion resistance properties.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

900# Steel Flanges Nickel Alloy Monel 400 Flange Bleed Ring the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

A standout feature of Monel flanges is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

The corrosion resistance of Monel K-500 is basically the same as Alloy 400, except that in the age hardened condition, Alloy K-500 has a greater tendency to stress corrosion cracking in certain environments. Monel K-500 has been found to be resistant to sour gas environments.

Monel 400 is well known for its high strength and corrosion resistant properties. It works in a wide range of temperatures, and is available in multiple forms for a variety of products. Monel 400 is used extensively in (for pipe) piping. Resistant to both steam and seawater, its toughness and anti-corrosive properties make it perfect for heavy duty applications such as transfer (pipe) piping used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

The alloy has great mechanical properties at subzero temperatures, and with a melting point of 2370¡ã ¨C 2460¡ã F, products can be used at temperatures up to 1000¡ã C.

The alloy is slightly magnetic at room temperature. Monel 400 is widely used in the chemical, oil and marine industries.

The Stud Bolt is a threaded rod with 2 heavy hexagon nuts, while the Hex Bolt has a head with one nut. Nuts and head are both six sided. Bolts threading are defined in ASME B1.1 Unified Inch Screw Threads, (UN and UNR Thread Form). The most common thread is a symmetrical form with a V-profile. The included angle is 60¡ã. This form is widely used in the Unified thread (UN, UNC, UNF, UNRC, UNRF) form as the ISO / metric threads.