semi-finished raw materials of Monel 400 Threaded Elbows made of the solid solution alloy

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

Monel 400 is resistant to both steam and seawater as well as highly caustic solutions such as sulfuric, hydrochloric, and hydrofluoric acids when they are deaerated.

The best machinability for these Monel K500 Lap Joint Flanges is in the annealed condition. Meanwhile, these Monel K500 Socket Weld Flanges are also being offered in different sizes and shapes to our customers.

These are widely used in various application industry. We also offer a wide range of monel 400 / K500 Flanges are available in various size, specification & thickness as per the clients requirements.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

Alloy K500 studs are threaded rods with threads on both ends. They can be of different types depending on thread distance from center and thread type. The material is resistant to high temperature and high pressure. It has a melting point of 1350 degrees Celsius, a minimum yield strength of 790MPa and a minimum tensile strength of 1100MPa. These values are twice as strong as level 304.

The increased properties are obtained by adding aluminum and titanimum to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated thoughout the matrix.

Socket weld flanges were originally developed for small high pressure pipelines. They have the same static strength as slip-on flanges, but their fatigue strength is 50% higher than double-welded slip-on flanges.

These Flanges are widely used in various application industries such as petroleum, chemical, construction, engineering, gas and shipbuilding industries and many more.

Monel 400 exhibits high strength, excellent resistance to acidic and alkaline environments, and good ductility and thermal conductivity.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

2.4375 Monel K500 round bar is non-magnetic, as an alloy, Monel K500 ASTM B865 hexagonal bar exhibits excellent mechanical properties over a temperature range from sub-zero settings to 480C. Monel ASTM B865 hollow bars require annealing when welded, and weldments should be stress relieved to the alloy prior to aging.

The classes define the pressure capacities. The monel 400 flanges have 63% nickel and 28% copper in the composition which makes them stronger.

Typical applications are valves and pumps; pump and propeller shafts; marine fixtures and fasteners.

Monel 400 is resistant to steam and sea water as well as highly corrosive solutions such as sulfuric, hydrochloric and hydrofluoric acids after degassing. It has excellent solderability and can withstand very high pressure and weight. The alloy has excellent mechanical properties at sub-zero temperatures, with a melting point of 2370¡ã – 2460¡ã F, and the product can be used at temperatures up to 1000¡ã C.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

Although ASTM B165 UNS N04400 material has lower strength in the annealed condition, it exhibits excellent mechanical properties even at sub-zero temperatures. Monel tubes can be used up to 1000 degrees Fahrenheit. In order to improve the mechanical properties of Monel 400 welded pipe, it is possible to make finished products on it.

When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

Monel 400 is a popular, high performance nickel-copper alloy commonly used in critical and high performance applications.

Monel K500 nuts are a result of an age hardening process where aluminum and titanium are added to the nickel-copper base and then precipitated throughout the matrix.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

Monel 400 and K500 flanges also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions.

The Monel Alloy 400 Threaded Flanges are fitted with pipes with threads. The male threads on the pipe ends fit with the female threads on the threaded flanges. The ASME SB564 Alloy 400 Socket Weld Flanges are usually welded onto the pipes.

ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. ASTM B 564 Monel K500 Lap Joint Flanges may be used at all pressures and are available in a full- size range. They can be salvaged for use in systems that erode or corrode quickly. We keep a tab on market trends and demands, to invent new, sustainable and economical products capable of undergoing customization. Our products are fully certified and 100% durable.

Monel nuts are often used for standard and advanced applications where high levels of strength and superior corrosion resistance is nearly always required. Monel 500¡¯s premium corrosion resistance, strength and usability in extreme conditions makes it the ideal choice for a wide range of industrial applications.

Reworking of Alloy K-500 is best done while the material is in the annealed or hot worked and quenched condition. However, age hardened materials can be finished to close tolerances and finish. Therefore, the recommended practice is to machine slightly oversize, age harden, and then finish to size.