1-4 SCH5S-SCHXXS stainless steel female pipe fitting cap

The Incoloy 825 consists of small amounts of copper, titanium, and molybdenum, contributing to its excellent mechanical properties. The Incoloy 825 Pipe Fittings have high resistance to pitting and crevice corrosion.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

Super Duplex S32950 Fittings are hardened on a variety of parameters such as strength, temperature, pressure resistance and durability before supplied to the customers. These UNS S32950 Super Duplex Pipe Fittings are being offered in an inclusive range such as S32950 Elbow, S32950 Bends, S32950 Equal & Unequal (reducing) Tees, S32950 Equal & Unequal (reducing) Cross, S32950 Concentric & Eccentric Reducer, S32950 End Pipe Cap, S32950 Long & Short Stub-ends, etc.

For the seamless steel pipe fittings refers to the fittings raw material from the seamless steel pipes and tubes. Thus the welded steel pipe fittings covers the fittings raw material from welded steel pipes.

Duplex UNS S32205 Pipe Elbows are used where the direction of the pipe must be changed and there is less stress on the pipe wall. Elbow is one of the most commonly used accessories. Most fittings have nominal bores ranging from 1/8″ to 42″.

Inconel 601 (N06601) Nickel-based alloy plasticity machinability.

AL-6XNalloy (UNS N08367) is a low carbon, high purity, nitrogen-bearing “super-austenitic” stainless alloy. The AL-6XN alloy was designed to be a seawater resistant material and has since been demonstrated to be resistant to a broad range of very corrosive environments. The high strength and corrosion resistance of the AL6XN alloy make it a better choice than the conventional duplex stainless steels and a cost effective alternative to more expensive nickel-base alloys where excellent formability, weldability, strength and corrosion resistance are essential.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel K500 pipe bend and elbow have corrosion resistance in an extensive range of marine and chemical environments. From pure water to non-oxidising mineral acids, salts and alkalis.

Super duplex 2507 / UNS S32750 pipe fittings have great resistive properties to chloride stress corrosion cracking and a high thermal conductivity with a low coefficient of thermal expansion. These pipe fittings have a great resistance to inorganic acids used in dilute hydrochloric acid.

Alloy 20 was originally developed for use in sulfuric acid service found in facilities such as pulp and paper mills. With good general corrosion properties, Alloy 20 usage has expanded in chemical, petrochemical and power generation plants.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The 316 stainless steel pipe bends can undergo processes, like cold forming and welding, where the austenitic crystal structure is transformed into ferromagnetic martensite. 316L steel is more susceptible to gaining some degree of magnetism.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

Our Duplex Steel S31803, S32205 Seamless Pipe Fittings are machinable and weldable and ductile even at low temperatures.

The alloys used to make these 304 stainless steel socket weld fittings are the most adaptable and widely used. UNS S30400 Short Radius Elbows can be used for high temperatures up to 889 degrees Celsius.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The dual-phase steel S31803/S32205 reducer suppresses deformation and cracking at high temperature, which is superior to ordinary steel parts in the chemical industry that are sensitive to chloride stress corrosion cracking.

Generally speaking, carbon steel pipe fittings and flanges are widely used in applications that do not require higher corrosion resistance materials such as stainless steel and nickel alloys. Carbon steel products are easy to corrode and rust when exposed to water.

Stainless Steel 304 Fitting Elbow is an austenitic chromium alloy with a steel composition of 18% chromium and 8% nickel. Stainless steel 304 pipe fittings have high ductility, excellent forming, spinning and drawing properties.

Some types of duplex steel pipe fittings are butt welded fittings, elbows, reducers, couplings, reducers, tees, adapters, joints, and more. Other features of this fitting are good corrosion resistance, pitting and crevice resistance, higher tensile strength, higher yield strength, good toughness, reliability, durability, oxidation resistance, mechanical properties, chemical properties Wait. In addition, it is used in the following applications in chemical industry, pulp and paper industry, condenser, offshore industry, etc.

ASTM A403 WP316 fittings are available in different sizes and shapes in pressure ratings 3000#, 6000# and 9000#. Stub end fittings are often used to close one end of a pipe.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

They are used in different applications with different purposes. ASTM A403 WP316 Elbow is used to change the direction of the pipe. When the elbow is made of 316 steel, it can be used in chloride-rich marine applications. Elbows can have different lengths and angles.

The nickel alloy is dual certified (800H/HT) and combines the properties of both forms. Incoloy 800H/HT alloy was intended for high temperature structural applications.

Carbon steel is a base steel composed of carbon and iron. It may contain other substances in unmeasured quantities or in trace amounts. Carbon steel is classified according to the carbon content mixed with iron. Medium and low carbon steels may have a carbon content of less than 0.3%, while high carbon steels may have carbon content as high as 2%. The percentage difference in content is usually chosen based on solderability. Carbon is known for its ability to withstand high temperatures and strength/stress.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

Monel 400 has excellent resistance to chloride ion stress corrosion cracking.

This concentric reducer has a high conductance tapered profile that reduces tube size. Butt weld joints are fabricated from welded, drawn and annealed 304 stainless steel tubing for applications where the number of sealed joints needs to be minimized.