Alloy steel ASTM A182 F5 F9 F11 F22 Flange

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

The flange connection type usually comes with double units, with a gasket and some bolts & nuts to connect each other. (Firstly pipes are welded on the flanges, then valves and other equipment could be installed on flanges.)

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength.

Monel 400? sheet is available in thicknesses ranging from .018 to .140″.Butt-weld and forged fittings are available or can be manufactured with short lead times.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

A320 Gr L7 studs are subject to certain mandatory mechanical tests, namely: tensile test, impact test and hardness test.

ASTM A335 P11 is part of ASTM A335, Pipe shall be suitable for bending, flanging, and similar forming operations, as well as fusion welding. The steel shall meet the requirements of chemical composition, tensile properties and hardness. Each pipe shall be hydrostatically tested. In addition, each pipe shall be inspected in accordance with the practice required for non-destructive testing.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.45

We have many years of experience in manufacturing ASME SA335 grade P9 alloy seamless steel pipe and provide high quality, low cost but best service.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.27

ASTM 182 is use in pressure systems, Included are flanges, fittings and similar parts to specified dimensions or to dimensional standards, such as the ASME specifications. 182 F5 Cl2 Alloy Steel Flanges are well suited to not only high temperature but also high pressure or a combination of both these applications.

The material contains carbon, manganese, phosphorus, sulfur, silicon, 8% chromium and molybdenum in a mixture. SA 335 grade P5 alloy steel pipe has similar strength to most austenitic stainless steel grades, with a minimum yield strength of 205MPa and a minimum tensile strength of 415MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P120

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel forged fittings, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

Bolts are chrome molybdenum heat treated steel according to ASTM A193 B7m specification for bolts. The primary alloy components of ASTM A193 Grade B7 bolts are chromium and molybdenum. These ASTM A193 B7 Metric Bolts are manufactured by heat quenching and tempering. Heat treating A193 B7 bolt material helps to develop desired mechanical properties such as increased tensile strength of ASTM A193 B7 hex bolts after heat treatment.

Chromium-Molybdenum alloy steel flanges dimensions has been widely used in the many areas. Their utilization can be seen in areas such as steam power equipment, petrol chemical industry, and high temperature services.

Nuts with a nominal size over 1 inch shall be a UNC Series Class 2B fit or an 8 UN Series Class 2B fit. High strength ASTM A194 grade 2H nuts are common in the market and are often replaced by ASTM A563 grade DH nuts due to the limited availability of DH nuts in certain diameters and finishes.

ALLOYS STEEL SA 182 F9 BAR is a ferritic alloy steel bar, other contents are also considered. These bars are steel forged bars held at high temperature and pressure.

Forged Pipe Fittings (Socket Weld and Threaded) are made in
accordance to ASME B16.11, MSS-SP-79/ 83/ 95/ 97 and BS3799
standards, and are used to connect nominal bore schedule pipes
and pipelines.

S32205 is a duplex stainless steel with twice the strength of austenitic stainless steel. Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance. The yield strength of duplex stainless steels is twice that of austenitic stainless steels, a feature that allows designers to reduce weight when designing products, making this alloy more affordable than 316, 317L. This alloy is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range. For applications outside this temperature range, this alloy can also be considered, but there are some limitations, especially when applied to welded structures. Duplex stainless steel has twice the compressive strength compared to austenitic stainless steel, and designers can reduce its weight compared to 316L and 317L. Alloy 2205 is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range, and can also be used at lower temperatures under severe restrictions (especially for welded structures).

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Shaped flanges made by die forging or precision (lost wax) casting, depending on the mechanical properties of the flange, die forged flanges have higher strength than cast flanges. Precision profiled flanges manufactured by forging or casting require a model (tool).

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

For the F5 flange, the creep strength of the chromium-molybdenum low alloy mainly comes from two sources: the solid solution strengthening of the matrix ferrite by carbon, molybdenum and chromium and the precipitation hardening of the carbides.

Grade P11 is known as chrome molybdenum alloy steel. Compared to carbon steel, the properties of this alloy steel are much higher. Typically, alloy steels such as ASTM A335 P11 pipe tend to have much higher element percentages than conventional steels. So take their efficiency to the next level. The alloy composition of the P11 grade consists of chromium and molybdenum, with a chromium percentage of approximately 1.25. The content of molybdenum in the alloy steel P11 seamless pipe is about 0.5%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P124

Applications for Alloy Steel A335 P5 EFW Tubing can be seen in petrochemical, oil and gas industrial applications, power plants and other high pressure and high temperature services.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P123

The skills of chromium alloy steel include higher oxidation corrosion rates. In addition to being resistant to oxidation, alloy steel P91 of A335 steel pipe is also able to withstand very high temperatures and can be used in applications involving boilers, heaters, power generation, and more. The above applications work based on elevated temperature, which is why many suppliers recommend alloy steel P91 pipe for the above applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.21

It must be slid into the pipe before welding. In this case, it’s a double weld on both sides (i.e. inside and outside), so it provides durability that helps avoid leaks.

High alloyed types of steel are favored in the plumbing industry for use in extreme conditions, be it hot or cold, or subjected to rough service. This is because a combination of chemistry and proper heat treatment can result in a strong and flexible pipe that can withstand blows. Alloy pipes are often favored by the oil and gas and power generation industries due to their toughness.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.43

Our ASTM A182 F5 alloy steel blind flanges are used in auxiliary industrial high pressure services such as heat exchangers, condensers, evaporators, boilers, etc.

ASTM A194 2h nuts are available in nominal sizes ranging from ?” to 4″. These products are made with heavy duty hex nuts with different proof load stresses for regular nuts and zinc plated nuts. A194 2h coupling nut with 175ksi plain nut and 150ksi zinc plated nut. Fasteners of this grade of material also have high hardness.

We also provide various alloy steel ASTM A182 F5 flanges, such as ASTM A182 F5 slip-on flanges, alloy steel F5 butt weld flanges, F5 alloy steel socket weld flanges, A182 F5 alloy steel blind flanges, alloy steel F5 Orifice Flange, A182 Alloy Steel F5 Blind Flange, A182 F5 Threaded/Threaded Flange, Alloy Steel F5 Reducing Flange, ASTM A182 F5 Alloy Steel Ring Type Joint Flange (RTJ) etc.

ASTM A182 F11 class 1 Flange is the method of connecting two pipes, pumps and valves. This consists of chromium molybdenum based alloy steel grade.

We use state-of-the-art technology to precisely manufacture flanges such as ASTM A182 Class F5 Socket Weld Flanges. Buying an ASME SA182 F5 flange or any other flange from us will guarantee quality, economy and precision.