UNS S32760 F55 super duplex square steel bar more cost effective than nickel alloys

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Though it is important to keep in mind that pitting corrosion can be a concern in chloride solutions when oxidizing media is present. In these conditions, the passive (protective) layer of the Duplex 2205 material may be compromised in localized pitting may occur.

Alloy 2205 Pipe has a melting point of 1350 degrees C. These pipes have a wall thickness between 0.3mm to 50mm.

2205 is also more formable under pressure than other ferritic grades. The greater toughness of this grade also outweighs most of its concerns.

The ASTM A790 Duplex Welded Pipes are an example of welded duplex pipe. There are different grades of duplex pipes with different mechanical properties. There are duplex, super duplex and lean categories in the Duplex Pipes varieties. The Seamless Duplex Pipes are both strong and is highly corrosion resistant.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

As experts in the field of fasteners, we recognize that this alloy can be used in a variety of applications including heat exchangers, piping, pressure vessels, tanks, fans, pulp and paper equipment, oilfield equipment and press rolls. At HT PIPE you can find Duplex Premium Gaskets in high quality.

Duplex 2205 is the most widely used duplex (ferritic/austenitic) grade of stainless steel. It is used due to its excellent corrosion resistance and high strength.

ASTM A240 UNS S32750 plate is suitable for high tension and high corrosion environments.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The composition of UNS S32750 super duplex steel strip contains chromium, nickel and molybdenum.

Duplex 2205 stainless steel (ferritic and austenitic) is widely used in applications requiring good corrosion resistance and strength. Grade S31803 stainless steel was modified several times, resulting in UNS S32205, which was recognized in 1996. This grade provides higher corrosion resistance If we do not stock Duplex 2205 fasteners (imperial or metric), we can manufacture these to your specifications.

The applications include high corrosive applications including acidic applications due to the material composition.

S32750 Seamless Pipes are chromium and molybdenum mixtures with high resistance to pitting. Many industries prefer these Seamless Pipes for their resistance to stress corrosion cracking and crevice corrosion.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Due to the ferritic portion of the duplex structure of the alloy it is very resistant to stress corrosion cracking in warm chloride containing environments.

Duplex 2507 possesses excellent mechanical properties. Often a light gauge of 2507 material can be used to achieve the same design strength of a thicker nickel alloy.

The ductility and corrosion resistance of duplex steel fasteners are reminiscent of their austenitic microstructure. On the other hand, the toughness and hardness of these fasteners are inherited from the ferritic region.

Super Duplex Steel Pipes and Tubes are available in various dimensions, shapes like square, rectangle, and so on and enormous sizes. We are offering the standard quality of products of our customers. Our Product is offering excellent corrosion resistance and remarkable dimensional accuracy.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

In general, duplex steel S31803 plate can be used as a replacement for the rather expensive stainless steel alloy grade 904L, as 2205 SS plate has similar properties but is less expensive in composition.

The 2205 Duplex Stainless Pipe exhibits magnetic properties in certain environments.

A Super Duplex 2507 Pipe has outstanding resistance to corrosive and oxidative media.

Grade 904L is less resistant to nitric acid than grades 304L and 310L, which are free of molybdenum. This steel grade needs to be solution treated following cold working, to achieve maximum stress corrosion cracking resistance under critical environments

We offer a complete range of 2205 Duplex Steel Fasteners such as Bolts, Nuts, Washers, Screws, Connecting Rods and Duplex Steel Screws. We also offer super duplex fasteners in different sizes, shapes, features and thicknesses according to customer requirements.

Astm A479 Super Duplex Steel UNS S32760 Hex Bolts have a high PREN value, the rate of pitting is lower, despite the use of these fasteners in highly corrosive environments such as oil wells and pipelines transporting soured oils, sulfide ores processing, kraft paper production plants, methionine and lysine factories, as well as the photographic industry.

ASTM A479 Super Duplex UNS S32750 Fasteners is a mixed microstructure of austenite and ferrite (50/50) which has improved strength over ferritic and austenitic steel grades.

The yield strength of this material is almost two times that of the usually used austenitic stainless steel grade.

2205 duplex stainless steel is a cost effective solution for many applications where the 300 series stainless steels are susceptible to chloride stress corrosion cracking. Stress corrosion cracking occurs when stainless steels are subjected to tensile stress, while in contact with solutions containing chlorides. Increasing temperatures also increase the susceptibility of stainless steels to stress corrosion cracking.

For many applications where 300 series stainless steel is susceptible to chloride stress corrosion cracking, 2205 duplex stainless steel is a cost-effective solution. Stress corrosion cracking occurs when stainless steel is subjected to tensile stress while in contact with solutions containing chlorides. Elevated temperatures also increase the susceptibility of stainless steel to stress corrosion cracking.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.52

The chemistry of this steel ensures better performance with higher mechanical properties in comparison to austenitic stainless steel pipes.

Another advantage of grade 304 stainless steel bar over grade 303 is that it is slightly harder and has better corrosion resistance. Because of this, grade 304 stainless steel bar is used in large quantities in the manufacture of fasteners and fixtures such as nuts, bolts, washers, clips, fittings and clamps. Products made from grade 304 stainless steel in the fastener industry are often referred to as “A2”.

The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of applications, there are some important technical weaknesses in both types.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance).
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.50