A182 F53 2507 special flange with ferrite microstructure and high impact strength

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

2205 flange has good general corrosion resistance, high resistance to chloride stress corrosion cracking, as well as pitting and crevice corrosion.

Duplex 2507 is usually used in Desalination Equipment, Chemical process pressure vessels, piping and heat exchangers and Marine Applications.

This grade, with a tighter specification, is captioned as F60, equating to UNS S32205. Consequently, S32205 can be dual-certified as S31803 but not vice-versa.

S31803 stainless steel is a nitrogen alloy duplex stainless steel containing 22% chromium, 3% molybdenum, and 5-6% nickel. In addition to high strength and excellent impact toughness, it also has high resistance to general corrosion, localized corrosion and stress. Corrosive properties.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.61

Super Duplex stainless for e.g. alloy UNS S32750, has a mixed microstructure of both austenite as well as ferrite in an equal or 50/50 ratio.

Duplex stainless steel fasteners are available in Super Duplex, Lean Duplex and Standard Duplex grades, each with specific properties for differenut applications.

Designers may have the option to reduce the wall thickness of the duplex 2205 welded pipe, because of its high yield strength. The yield strength of this material is almost two times that of the usually used austenitic stainless steel grade. Unlike austenitic steel pipe, the Duplex 2205 Tube may at times exhibit magnetic behavior because the microstructure of its alloy contains about 50% ferrite.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

In general, duplex steel S31803 plate can be used as a replacement for the rather expensive stainless steel alloy grade 904L, as 2205 SS plate has similar properties but is less expensive in composition.

The SA 182-F51 S31803 comes under ASME B16.47, B16.48 and B16.5 standards with sizes ranging from 1/8 NB to 48NB.

2507 Duplex is highly resistant to uniform corrosion by organic acids such as formic and acetic acid.

The idea of duplex stainless steels dates back to the 1920s with the first cast being made at Avesta in Sweden in 1930. However, it is only in the last 30 years that duplex steels have begun to ¡°take off¡± in a significant way. This is mainly due to advances in steelmaking techniques particularly with respect to control of nitrogen content.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Super Duplex is used in gas and oil industry, on offshore platforms, chemical processing equipment pressure vessels and boilers, in heat exchangers.

ASTM A479 Duplex Steel UNS S31803 Nuts have excellent general corrosion resistance in a variety of aggressive chemicals including seawater and industrial acids. The microstructure of ASME SA 479 Duplex Steel UNS S32205 Hex Nuts consists of a mixture of austenitic and ferritic phases. Therefore, it exhibits the properties of austenitic and ferritic stainless steels.

The ASTM A182 F51 flanges refer to standard or non-standard flanges manufactured in accordance with ASTM A182 Grade F51, which is designated with UNS number S31803.

ASTM A815 specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction. Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Teel Industry has grown in the past few decades and there are a variety of products available in the market. ASTM A815 UNS S32750 Pipe Fittings are one of those products and are available in various sizes, shapes, and dimensions. ASTM A815 UNS S32760 Pipe Fittings are designed to be resistant to corrosion and are said to have perfect weldability. These Super Duplex S32750 Buttweld Fittings are resistant to erosion corrosion and fatigue. They have a mixed microstructure of 50% austenitic and 50% ferrite.

The equivalent proportions of their existence make it possible for the alloy to express qualities reminiscent of each steel type. Take austenitic steels, where the most basic grade, like 790 steel duplex pipe, has substantial corrosion resistance properties.

Duplex 2205 is a nitrogen enhanced duplex stainless steel designed to solve common corrosion problems encountered with 300 series stainless steels. “Duplex” describes a family of stainless steels that are neither fully austenitic (such as 304 stainless steel) nor purely ferritic (such as 430 stainless steel).
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.48

Technically, the microstructure of a duplex 2205 tube is approximately 50% ferrite and 50% austenite. As a result, the properties inherited from both categories make this nitrogen-enhanced duplex 2205 seamless pipe ideal for use in industries such as food processing, oilfield piping and heat exchangers, and flue gas desulfurization.

Due to the alloy’s very high mechanical strength, dual-phase fastener manufacturers can reduce the weight of their designs by thinning the cross-section of the final product, proving a cost-saving alternative to other grades of stainless steel.

The service temperature of 2205 duplex stainless steel should be limited to below 600¡ãF. Prolonged exposure to high temperatures can make 2205 stainless steel brittle.

It is a tee fitting with two outlets at a 90¡ã junction to the main line.

Super Duplex UNS S32750 /F53 Flanges are made from a super duplex stainless steel grade that has 24% chromium, 3% molybdenum, 6% nickel and carbon, manganese, silicon, sulfur, phosphorus, nitrogen and iron in the composition.

Alloy 2507 is a high strength duplex alloy. Super Duplex Plate is a dual ferritic and austenitic microstructured component designed with high concentrations of chromium, nickel and molybdenum. Super Duplex 2507 plate is used in systems where extra strength and enhanced corrosion resistance of different systems are required.

ASTM A479 Super Duplex UNS S32750 F53 Heavy Hex Nuts are kept together by a combination of their threads’ friction (by means of slight elastic distortion), a small widening of the bolt, and solidity of the components to be held together.

The material of the super duplex S32750 sheet has increased tensile strength and yield strength. Super Duplex Steel UNS S32750 plate has good ductility and toughness. AISI S32750 plate has good corrosion resistance compared to Duplex. The material of the super duplex steel S32750 plate has higher corrosion resistance.

The S31803 fastener series demonstrates the properties of ferritic and austenitic stainless steels. These fasteners exhibit excellent resistance to crevice corrosion, stress corrosion cracking and pitting corrosion in harsh environments. In addition, these are excellent in resistance to chloride and sulfide stress corrosion environments.

We manufacture and supply bar stock for machined, forged and cold formed Duplex 2205 Nuts. We can manufacture and supply Duplex 2205 nuts in imperial sizes from M2 to M150 and 1/4″ to 6″. The most commonly used nuts are heavy hex nuts, flange nuts, cap nuts, set nuts, etc. We can supply these duplex 2205 nuts with minimal lead time.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance).

The flanges could also be manufactured as screwed, threaded or forged types. The forged flanges are made from a single piece of raw material. These are also called the cast flanges.

ASTM A240 UNS S32750 sheet is a type of steel known as super duplex steel.