A420 WP L3 WP L6 elbow used in food industries chemical industries and electrical industries

Alloy steels contain varying proportions of alloying elements (such as manganese, silicon, nickel, titanium, copper, chromium, and aluminum) to control steel properties such as hardenability, corrosion resistance, strength, formability, weldability, or ductility . The differences are somewhat uniform, but for the sake of distinction, all alloy steels over 8% by weight, not carbon and alloys, are considered high-alloy steels. Alloy steel is harder, more durable, and more resistant to corrosion. Alloy steels with moderate to high carbon content are difficult to weld. However, if the carbon content is reduced to 1% to 3%, this alloy metal can achieve higher formability and weldability, thereby increasing strength.

For instance, the use of Carbon Steel ASTM A105 Fittings is prominent in those applications that involved not only environments where the temperatures are high, but also in those applications at room temperature.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

a105 blind flange is forged between 1,700¡ãF to and 2,200¡ãF, followed by quenching and tempering.

There are studs, washers, threaded rods, screws, etc. Each type of fastener has its own advantages and application requirements. Carbon steel screws can be used without nuts. It can be driven with a screwdriver.

Carbon steel is a steel in which the main alloying element is carbon. Steel is considered carbon steel when there are no minimum requirements for chromium, cobalt, molybdenum, nickel, titanium, tungsten or other alloying elements. Carbon steel can be made harder and stronger through heat treatment. These hardness and strength measurements are determined by the carbon content – the higher the carbon content, the harder and stronger the steel will be.

A350 LF3 material is often referred to as low temperature carbon steel fittings or flanges.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Flanges, fittings, valves and other components in the A694 specification are suitable for high pressure transfer service.

The combination of all elements of the bolt accounts for 10% of the weight of the steel. As the name suggests, HSLA bolts are heat treated for higher strength. These washers remain ductile, making them easy to form and machine, while exhibiting higher corrosion resistance than ordinary mild steel.

All SA234 WPB Elbow are manufactured in India and produced from strictly European sourced raw material. All ASTM A234 Elbow & Elbow A234 Wpc are manufactured from plate, pressed in two halves with two weld seams.

A234 WPB Elbow is produced and supplied in the butt welded form. SA234 WPB Elbow usually comes in either of three angles; 22.5, 45 or 90 degrees.

U-Bolts are easy to machine and can meet the tight tolerances required for thread and fastener configurations. Carbon steel is also an economical metal. Carbon steels are classified by the amount of carbon in the alloy, which affects the properties of the steel. Mild steel with a carbon content of 0.05-0.3% is ductile and ductile. Low tensile strength and hardenable by carbonization. It is the lowest cost of carbon steel alloys.

A105 carbon steel round bars contain carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum and vanadium.

,ANSI B16.5 A105 Weld Neck Flange,A105N Weld neck flange,A105 weld neck flange,A105 Bind flange,A105 Slip on Flanges

To strengthen and harden the steel and cast iron alloy Carbon Steel Slip On Flanges are passed through a process known as quenching.

This specification covers standards for forged carbon steel piping components, that is, flanges, fittings, valves, and similar parts, for use in pressure systems at ambient and higher-temperature service conditions

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

ASTM A234 WPB Elbow is a standard specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel suitable for for Moderate and High Temperature Service.

The ASTM A333 Grade 6 low alloy steel seamless pipes are intended for low temperature services with minimum design temperature -45°C [-50°F] requiring notch toughness. They are usually furnished in nominal pipe size (NPS) and nominal wall thickness with schedule numbers in accordance with ASME B36.10M.

Our astm a694 f60 round bars are accepted by customers in a variety of industries, from basic industries such as sugar, paper, textile, dairy, engineering, to more complex industries such as oil and gas, petrochemical, chemical and fertilizer, power generation, and nuclear industry.

ASTM A106 Seamless Pressure Pipe (also known as ASME SA106 Pipe) is commonly used in the construction of oil and gas refineries, power plants, petrochemical plants, boilers, and ships, where the pipes must transport fluids and gases with higher temperature and pressure levels .

A105 flange These are developed and produced in different shapes and forms. Carbon Steel Flange with their welded necks are good picks for piping with bending stress crack risk.

Welding neck flange have two forms (shapes), one with reducing neck as we called reducing weld neck flange; One with a even diameter of typical long neck named as long neck weld flange.

Stainless steel is an alloy of iron that is resistant to rusting. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel’s resistance to corrosion results from the chromium, which forms a passive film that can protect the material and self-heal in the presence of oxygen.

Knowing the finish of these steels can be helpful if your pipes are visible and appearance is on the list of considerations. Stainless steel is usually glossy and can retain that gloss if exposed to weather and other factors. Carbon steel, on the other hand, is darker in color and usually has a matte finish when painted. Unfortunately, it can also rust and look bad if left exposed. Galvanizing is also an option.

The A420 Grade WPL6 fitting is used in pipelines in the paper and pulp industries, condensers, sea water, marine engineering, waste water management and pollution control systems.

As an ISO certified company, we stand by the principles of quality, safety, and precision in all our products.

These ASTM A350 Flanges LF3 are suitable for use down to 150oF (LF3). These LTCS A350 LF3 orifice plate flanges are basically used in high energy/high temperature channel systems.