acero inoxidable tubos y tuberias ASTM A790 S32750 1.4410

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

At temperatures above 300¡ãC, the brittle trace components of 2205 precipitate, and at temperatures below -50¡ãC, the trace components undergo a ductile-brittle transition; therefore, this grade of stainless steel is not suitable for use at these temperatures.

Duplex steel UNS S31803 round bar is widely used for ferritic and austenitic duplex stainless steel bars.

This grade, with a tighter specification, is captioned as F60, equating to UNS S32205. Consequently, S32205 can be dual-certified as S31803 but not vice-versa.

Duplex stainless steels have a mixed microstructure of austenite and ferrite, the aim being to produce a 50/50 mix, although, in commercial alloys, the mix may be 40/60 respectively.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

An austenitic-ferritic stainless variant with a higher stress corrosion cracking resistance in comparison to regular austenitic 304 and 316 stainless, but with a lower toughness and impact strength.

Supplied in the annealed condition, it has a yield strength of 80ksi (550Mpa), which is higher than most austenitic and duplex grades.

We are a manufacturer of Stainless Steel Round Bar, Formed Steel and Rebar, we supply bars such as 304, 304l, 316, 316l and 347. We are proud to have the largest share of stainless steel forming steel in the country.

ASTM A240 Type 2205 Duplex Sheet provides a maximum Brinell hardness value of approximately 290 in the annealed condition.

Duplex pipes are stainless pipes containing the high amount of chromium and minimum amount of nickel. Duplex pipes provide great strength and resistance to corrosive environments. Duplex pipes are used in desalination plants, heat exchangers, and marine processes.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

ASTM A240 UNS S32750 plate is suitable for high tension and high corrosion environments.

Zeron 100?contains 25% chromium and 7% nickel and 3.6% molybdenum along with copper and tungsten additions. Zeron 100 has a 50¨C50 austenitic¨Cferritic structure. It also has greater resistance to chloride pitting, crevice corrosion and stress corrosion cracking than exhibited by the standard 300 series stainless steels.

2507 Super Duplex Stainless Steel was designed for demanding applications which require exceptional strength and corrosion resistance, such as chemical process, petrochemical, and seawater equipment.

2205 duplex grade without requiring higher levels of nickel or molybdenum. This means that it is a low-cost option than most austenitic stainless steel having the same requirements.

Unlike the conventionally used austenitic 300 series stainless steels, duplex stainless steels generally have exaggerated properties. Duplex tube suppliers recommend using only this alloy as it combines both properties to produce positive results.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.55

Due to the material composition, the strength and the corrosion resistance, these flanges are used in a variety of applications.

2507 Duplex Plate also exhibit better ductility and toughness compared to ferritic stainless steels, but they do not provide these properties as successfully as austenitic stainless steels.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

There are components of duplex 2205 fasteners available such as studs, set screws, bolts, washers and nuts. Whenever you specifically consider duplex stainless steel 2205 gaskets, it can be of great benefit for different types of critical industrial applications often found in harsh environments. Almost all types of 2205 stainless steel gaskets will provide a never-ending supply and excellent range of service for different applications such as valves or nuclear, seawater, offshore buoyancy and petrochemical, pumps, etc.

This provides the flanges with high corrosion resistance and higher mechanical properties. Please contact us for your orders of F53 flanges.

Duplex 2205 stainless steels are called “duplex” because they have a two-phase microstructure consisting of ferritic and austenitic stainless steel grains. When duplex stainless steel melts, it solidifies from the liquid phase to a fully ferritic structure. As the material cools to room temperature, about half of the ferrite grains transform into austenite grains (“islands”). The result is a microstructure of approximately 50% austenite and 50% ferrite.

At this temperature, duplex steel flanges over 300 degrees Celsius are still protected from embrittlement due to corrosion. Duct capability is also excellent at low temperatures. Fabrication is done only with tools assigned to stainless steel materials. Must be properly cleaned before use. This is done to protect the stainless steel from cross-contamination of the corroding metal.

ASME SA 479 Duplex Steel UNS S32205 Hex Bolts are commonly used in chemical processing, transportation and storage – pressure vessels, tanks, piping and heat exchangers. ASTM A479 Duplex Stainless Steel 1.4462 Bolts have excellent resistance to stress corrosion cracking, as well as excellent resistance to localized corrosion, including intergranular, pitting, and crevice corrosion.

The SA 182-F51 S31803 comes under ASME B16.47, B16.48 and B16.5 standards with sizes ranging from 1/8 NB to 48NB.

Duplex steel UNS S32205 fasteners are used in the pulp and paper industry such as digesters, bleach plants and stock handling systems. Also known as WNR 1.4462 fasteners, they are developed and designed in our infrastructure to international quality standards to the highest quality standards.

2205 duplex stainless steel is a cost effective solution for many applications where the 300 series stainless steels are susceptible to chloride stress corrosion cracking. Stress corrosion cracking occurs when stainless steels are subjected to tensile stress, while in contact with solutions containing chlorides. Increasing temperatures also increase the susceptibility of stainless steels to stress corrosion cracking.

Duplex 2205 Tube may at times exhibit magnetic behavior because the microstructure of its alloy contains about 50% ferrite.

Duplex stainless is a mixed microstructure of austenitic and ferrite (50/50) which has improved strength over ferritic and austenitic steel grades with similar corrosion resistance qualities.

2507 has good weldability and workability, and it’s widely used in desalination equipment, chemical process pressure vessels, piping and heat exchangers.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of applications, there are some important technical weaknesses in both types.