A182 F51 2205 S31803 flange ring with the minimum yield strength 450MPa

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

The combination of chromium, molybdenum and nitrogen give Duplex 2205 flanges good protection from chloride pitting and crevice corrosion, which makes them useful for marine environments, brackish water, bleaching operations, closed loop water systems and some food processing applications.

UNS S32750 or DIN W.Nr. 1.4410, Duplex 2507 is a super duplex stainless steel conutaining 25% chromium, 4% molybdenum and 7% nickel, designed for demanding applications requiring exceptional strength and corrosion resistance, such as chemical Process, petrochemical and seawater equipmenut.

Due to the material composition, the strength and the corrosion resistance, these flanges are used in a variety of applications.

Duplex 2205 is a nitrogen enhanced duplex stainless steelthat was developed to combat common corrosion problems encountered with the 300 series stainless steels. ¡°Duplex¡± describes a family of stainless steels that are neither fully austenitic, like 304 stainless, nor purely ferritic, like 430 stainless. The structure of 2205 duplex stainless steel consists of austenite pools surrounded by a continuous ferrite phase. In the annealed condition, 2205 contains approximately 40-50% ferrite. Often referred to as the work horse grade, 2205 is the most widely used grade in the duplex family of stainless steels.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

At this temperature, duplex steel flanges over 300 degrees Celsius are still protected from embrittlement due to corrosion. Duct capability is also excellent at low temperatures. Fabrication is done only with tools assigned to stainless steel materials. Must be properly cleaned before use. This is done to protect the stainless steel from cross-contamination of the corroding metal.

The corrosion resistance comes from the addition of alloying material, mostly the chromium content. The ASTM A790 Pipes are resistant to pitting corrosion and crevice corrosion.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

ASTM A479 Super Duplex 2507 Hex Bolts combines high strength and good ductility with outstanding corrosion resistance qualities. The higher chromium, molybdenum and nitrogen contents in these ASME SA 479 Alloy 2507 Hex Bolts result in a Pitting Resistance Equivalent number (PREN) of >40.

The pressure ratings of the material are designated by classes 150Lbs through 2500LBs. There are different types of the duplex f51 flanges such as the raised face, ring type joint and flat face flanges.

Compared with ferritic stainless steel and austenitic stainless steel, duplex stainless steel pipe has good welding performance. It is neither like the welding heat affected zone of ferritic stainless steel, because of the grain coarsening, the plastic toughness is greatly reduced, nor like austenitic stainless steel, it is more sensitive to welding hot cracks.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The fatigue strength of S31803 nuts is also very good under all extreme conditions. Duplex stainless steel UNS S31803 nuts also have good fatigue strength and excellent resistance to stress corrosion cracking, cracking, pitting, erosion, etc.

Alloy 2507 is a high strength duplex alloy. Super Duplex Plate is a dual ferritic and austenitic microstructured component designed with high concentrations of chromium, nickel and molybdenum. Super Duplex 2507 plate is used in systems where extra strength and enhanced corrosion resistance of different systems are required.

These plates combine desirable properties of austenitic and ferritic grades.

2205 flange has good sulfide stress corrosion resistance and high strength and good fatigue resistance.

Super Duplex UNS S32750 /F53 Flanges are made from a super duplex stainless steel grade that has 24% chromium, 3% molybdenum, 6% nickel and carbon, manganese, silicon, sulfur, phosphorus, nitrogen and iron in the composition.

Alloy 2205 provides pitting and crevice corrosion resistance superior to 316L or 317L austenitic stainless steel tube in almost all corrosive media. It also has high corrosion and erosion fatigue properties as well as lower thermal expansion and higher thermal conductivity than austenitic.

2205 is the most widely used duplex (ferritic/austenitic) stainless steel grade. It finds applications due to both excellent corrosion resistance and high strength.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Super Duplex 2507 is used in environments containing high levels of chlorides or dissolved oxygen, such as seawater cooling, salt evaporation, and desalination, geothermal wells.

The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of applications, there are some important technical weaknesses in both types.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The higher percentage of chromium in the alloy of duplex stainless steel seamless pipe makes it resistant to oxidation.

Alloy 2205 Pipe has a melting point of 1350 degrees C. These pipes have a wall thickness between 0.3mm to 50mm.

2507 has high resistance to stress corrosion cracking (especially chloride stress corrosion cracking), high energy absorption, high strength, and erosion. Essentially, and the Duplex alloys are a compromise.

Duplex stainless steel fasteners are made from alloys with high chromium content and low to moderate nickel content.

Duplex 2205 stainless steel round bars (ASTM A276/ ASTM A479) exhibit good heat resistance up to 300¡ã. SS Rod can be easily welded by most standard methods, the only mandatory requirement is the use of filler metal. Due to its high strength, machinability is low.

The temperature in heat exchange is usually increased because they work according to the principle of heat transfer. While A789 tubing can hold its own at high temperatures, it is not recommended for use in temperatures above 600F. Duplex 2205 Tube may become brittle and rot at temperatures above 600F.

UNS S31803 Bolt is a threaded fastener with external threads. Generally, like screws, alloy S31803 bolts tend to use a variety of head designs.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Duplex2205 washers are dual phase austentic-ferritic duplex fasteners manufactured from alloy containing chromium, nickel alloy and molybdenum with restricted carbon content and minimum PREN35, SAF2205 fasteners have excellent corrosion resistance and high strength.

2507 (PREN 40-45), with 25-26 Cr and increased Mo and N compared with the 25Cr grades. A super austenitic-ferritic duplex stainless steel with exceptional strength and corrosion resistance ideal for chemical process, petrochemical, and seawater applications.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

We are a manufacturer of Stainless Steel Round Bar, Formed Steel and Rebar, we supply bars such as 304, 304l, 316, 316l and 347. We are proud to have the largest share of stainless steel forming steel in the country.