Duplex stainless steel S32760 1.4501 Zeron 100 spring lock washer DIN127

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Las laminas duplex son grados austenitico-ferriticos con la misma composicion. Esta dise?ado para proporcionar laminas resistentes a la corrosion y de alta resistencia. Utiliza un mayor contenido de cromo hasta un 28%. La placa ASTM A240 UNS S32750 tiene un limite elastico minimo de aproximadamente 77 ksi y una resistencia a la traccion de al menos 730 MPa. Se estiro un 25% en estado recocido.

As well as greater tensile and yield strength whilst still providing good ductility and resistance to stress corrosion cracking.

In comparison to SS316, Duplex 2205 has been tested under reverse bending stresses at room temperature. The results show that the fatigue limit/yield strength is about twice as high for Duplex 2205.

Super Duplex is used in gas and oil industry, on offshore platforms, chemical processing equipment pressure vessels and boilers, in heat exchangers.

Duplex 2205 bolts have a ductile to brittle transition at -50¡ãC and also become brittle at 300-1000¡ãC, so a temperature of -50¡ãC to 300¡ãC is recommended. Exposure to above 300¡ãC will not only cause embrittlement of 2205 bolts, but will also reduce corrosion resistance.

Super Duplex S32760 Bar proves to be an excellent replacement for austenitic grades in marine environments. Super Duplex S32760 round bar (ASTM A276/ ASTM A479) exhibits good heat resistance up to 300¡ã.

2205 is the most widely used duplex (ferritic/austenitic) grade of stainless steel. It is used due to its excellent corrosion resistance and high strength. Over the years, many steel suppliers have made improvements to the standard duplex S31803 composition, and the resulting restricted composition range was recognized as UNS S32205 in 1996.

La tuberia SA 790 UNS S32205 se utiliza para aplicaciones que funcionan en ambientes ligeramente corrosivos, de presion y temperatura ligeramente alta. Aplicacion de tuberia sin costura Duplex S32205 UNS en sistemas de purificacion de agua y manejo de aguas residuales y alta precision.

Duplex 2205 stainless steel (ferritic and austenitic) is widely used in applications requiring good corrosion resistance and strength. Grade S31803 stainless steel was modified several times to form UNS S32205, which was recognized in 1996.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

On average, duplex stainless steel is about twice as strong as either ferritic or austenitic stainless steels. High toughness and ductility. Duplex stainless steel can be more easily formed under pressure than ferritic grades and also have superior toughness.

Duplex stainless steel has an array of various benefits such as:
Strength:Duplex stainless steels have approximately double the strength of regular austenitic or ferritic stainless steels.
Toughness and ductility:Duplex stainless steels exceed the toughness and ductility of ferritic grades although they are not as touch as austenitic grades.
Corrosion resistance:As with all stainless steels, corrosion resistance depends mostly on the composition of the stainless steel, with chromium, molybdenum and nitrogen content being the most important. Duplex stainless steels are extremely corrosion resistant and even in chloride and sulphide environments, duplex stainless steels exhibit very high resistance to stress corrosion cracking (SCC). SCC is a type of corrosion that takes place when a particular set of factors are present: Tensile stress, corrosive environment and a sufficiently high temperature.
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

2507 has Combination of properties given by austenitic and ferritic structure, and Good weldability and workability.

2205 dual-phase steel fasteners have some excellenut mechanical properties, which may be due to the balanced austenitic and ferritic microstructures in the alloy.

Duplex2205 washers are dual phase austentic-ferritic duplex fasteners manufactured from alloy containing chromium, nickel alloy and molybdenum with restricted carbon content and minimum PREN35, SAF2205 fasteners have excellent corrosion resistance and high strength.

The high chromium, molybdenum, and nickel levels provide excellent resistance to pitting, crevice, and general corrosion.

2507 is also used in Flue Gas Scrubbing Equipment, Pulp and Paper Mill Equipment, Offshore Oil production/technology and Oil and gas industry equipment.

The A182 Gr. F51 / S31803 material is a typical duplex stainless steel, which contains approximately 50% ferrite and 50% austenite.

The temperature in heat exchange is usually increased because they work according to the principle of heat transfer. While A789 tubing can hold its own at high temperatures, it is not recommended for use in temperatures above 600F. Duplex 2205 Tube may become brittle and rot at temperatures above 600F.

Duplex 2507 (UNS S32750) is a super duplex stainless steel with 25% chromium, 4% molybdenum, and 7% nickel designed for demanding applications which require exceptional strength and corrosion resistance, such as chemical process, petrochemical, and seawater equipment.

2205 duplex stainless tubing material, which is why it is referred to as a self-repairing layer.

Duplex steel UNS S32205 round bar has excellent corrosion resistance and resistance to localized corrosion such as intergranular corrosion, crevice corrosion and pitting corrosion.

The Super Duplex 2507 Pipe is made with 25% of chromium, 4% of molybdenum, and 7% of nickel in their composition. As a result, these pipes possess superior corrosion and erosion resistance in various stress-induced environments.

ASTM A815 specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction. Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Teel Industry has grown in the past few decades and there are a variety of products available in the market. ASTM A815 UNS S32750 Pipe Fittings are one of those products and are available in various sizes, shapes, and dimensions. ASTM A815 UNS S32760 Pipe Fittings are designed to be resistant to corrosion and are said to have perfect weldability. These Super Duplex S32750 Buttweld Fittings are resistant to erosion corrosion and fatigue. They have a mixed microstructure of 50% austenitic and 50% ferrite.

Super Duplex UNS S32750 bar has excellent resistance to stress corrosion cracking in chlorine containing environments. After heating to a solution treatment temperature of 1080¡ãC to 1120¡ãC, quenching is required.

Duplex 2205 stainless steels are called “duplex” because they have a two-phase microstructure consisting of ferritic and austenitic stainless steel grains. When duplex stainless steel melts, it solidifies from the liquid phase to a fully ferritic structure. As the material cools to room temperature, about half of the ferrite grains transform into austenite grains (“islands”). The result is a microstructure of approximately 50% austenite and 50% ferrite.

SA 815 S31803 Weld Fittings have exceptional chemical properties along with higher strength and good resistance to corrosion. Therefore this grade is used for fitting manufacturing. SA 815 S31803 Long/ Short Radius Elbow display outstanding resistance to pitting, crevice corrosion and have excellent weldability. They are perfect if one is looking for a sturdy pipe with good formability. ASME B16.9 WPS UNS S31803 Elbow also exhibits excellent resistance to acetic and marine environments.

The pressure-temperature ratings for ASTM A182 F53 flanges are the same as that for other duplex stainless steels.

This alloy resists chloride environments and sulfide stress corrosion. It is also roughly double the strength of standard austentic stainless steels.

Flat and lock washers can be cut or stamped from sheet to customer specifications. Since 2205 combines high strength, excellent corrosion and stress corrosion cracking resistance with very good pitting corrosion resistance and low thermal expansion, this may be the right alloy for your project nuts, bolts, spacers and studs.