2507 S32750 plate exceptional strength and corrosion resistance

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Duplex steel UNS S31803 hex nuts are widely suitable for the effects of sulphurous gases, especially above 900 degrees Celsius, very low.

As well as greater tensile and yield strength whilst still providing good ductility and resistance to stress corrosion cracking.

The properties of S31803 nuts are even double those of standard austenitic grades.

Duplex 2205 round steel contains 22% chromium, 3% molybdenum, and 5-6% nickel. In addition to excellent impact toughness and high strength, it also has high general, local and stress corrosion resistance.

ASTM A479 Duplex Steel UNS S32205 Round Gaskets are nitrogen reinforced duplex alloys formed to address common corrosion problems found incidentally with 300 series alloys. ASME SA 479 Duplex Steel UNS S31803 Machined Washers are hardened at 1868 to 1958 degrees Fahrenheit and then water quenched.

Duplex 2205 fasteners have high toughness and hardness while also possessing high levels of tensile strength, all as a result of the chromium present in them. However, it can be concluded that dual phase steel fasteners are undeniable; neither deformed nor damaged. This anomaly is much less likely to happen. 2205 Duplex Fasteners consume delicate structures made from ferritic and austenitic stainless steels that are considered part of an alloy, and the end result provides excellent mechanical properties in duplex fasteners.

2507 (PREN 40-45), with 25-26 Cr and increased Mo and N compared with the 25Cr grades. A super austenitic-ferritic duplex stainless steel with exceptional strength and corrosion resistance ideal for chemical process, petrochemical, and seawater applications.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

In the annealed condition, S31803 contains approximately 40-50% ferrite. S31803 is often referred to as the workhorse grade and is the most widely used grade in duplex stainless steel pipes. The use of S31803 stainless steel pipe should be limited to temperatures below 600¡ãF.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.64

The service temperature of 2205 duplex stainless steel should be limited to below 600¡ãF. Prolonged exposure to high temperatures can make 2205 stainless steel brittle.

Phase stainless steel UNS S31803 fasteners exhibit the properties of austenitic and ferritic stainless steels. UNS S31803 dual phase steel fasteners have high strength, good resistance to sulfide stress corrosion and excellent impact toughness.

The different face types have their own advantages in piping applications.

Super Duplex is composed of 24% to 26% chromium, 6% to 8% nickel, 3% molybdenum and 1.2% manganese, with the remainder being iron. Trace amounts of carbon, phosphorus, sulfur, silicon, nitrogen, and copper were also found in Super Duplex.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

S31803 has been supplemented by S32205 (F60) which has a higher minimum Ni Cr and Mo.

2507 nuts are highly resistant to carbide-related intergranular corrosion due to their low carbon content (0.020% in weight).

Some steels also contain the alloy elements such as Mo, Cu, Nb, Ti and N, etc. Compared with ferritic stainless, duplex stainless steel has higher plasticity, ductility and better intergranular corrosion resistance and weldability.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

This increase in alloyants is what gives the super duplex stainless steels greater corrosion resistance properties.

Application fields of duplex stainless steel:
¡¤ Pressure vessels, high-pressure storage tanks, high-pressure pipelines, heat exchangers (chemical processing industry).
¡¤ Oil and gas pipelines, heat exchanger fittings.
¡¤ Sewage treatment system.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance).
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.50

2507 has high resistance to stress corrosion cracking (especially chloride stress corrosion cracking), high energy absorption, high strength, and erosion. Essentially, and the Duplex alloys are a compromise.

ASTM A182 F53 flanges refer to flanges made from super duplex stainless steel 2507 (UNS S32750) by a hot forging process.

Duplex 2205 was tested under reverse bending stress at room temperature compared to SS316. The results show that Duplex 2205 has approximately twice the fatigue limit/yield strength.

Astm A182 F51 flange is made up of carbon, chromium, manganese, silicon, phosphorus, sulfur, nickel, nitrogen, molybdenum and iron.

These plates combine desirable properties of austenitic and ferritic grades.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Duplex steel UNS S31803 round bar is widely used for ferritic and austenitic duplex stainless steel bars.

Duplex UNS S32205 fasteners are widely used in construction and other industrial applications. We offer these types of fasteners in differenut thicknesses and tolerance limits for a variety of industrial applications.

2205 flange has good sulfide stress corrosion resistance and high strength and good fatigue resistance.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Super Duplex 2507 has more than twice the strength of conventional austenitic stainless steels in the annealed condition.

Type: Seamless, Welded

WT: SCH5-SCH80S