Super Duplex stainless steel S32750 1.4410 F53 spring lock washer DIN127

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

The presence of ferrite in the duplex 2205 welded pipe is what provides for an enhanced performance of this stainless steel grade in caustic media containing environments.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The Benefits of Duplex Stainless Steel are improved Strength, because many duplex grades are as much as two-times stronger than austenitic and ferritic stainless steel grades, high Toughness and Ductility, high Corrosion Resistance, and Cost Effectiveness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

ASTM A815 specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction. Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Teel Industry has grown in the past few decades and there are a variety of products available in the market. ASTM A815 UNS S32750 Pipe Fittings are one of those products and are available in various sizes, shapes, and dimensions. ASTM A815 UNS S32760 Pipe Fittings are designed to be resistant to corrosion and are said to have perfect weldability. These Super Duplex S32750 Buttweld Fittings are resistant to erosion corrosion and fatigue. They have a mixed microstructure of 50% austenitic and 50% ferrite.

Duplex 2205 flanges are made from an austenitic-ferritic stainless steel, which was designed to deliver higher strength and corrosion resistance than 300 series stainless steels.

Super Duplex Pipe Suppliersis known to have better pressure erosion, splitting obstruction and mechanical properties than some other kind of steel.

SA 182 F53 S32750 Flange is a super duplex stainless steel supplied in the hot worked and solution annealed condition.

Alloy 2205 gets the name Duplex because it is composed of two different types of grains. 40-50% of its grain structure is austenite and 50-60% of it is ferrite. It is closely related to, but much more popular than Alloy 255. In most environments, it surpasses 317L in crevice corrosion resistance. 2205 Duplex excels in chloride environments and resists hydrogen sulfide. 2205 Duplex has almost twice the strength of 316L. Due to the lower nickel and molybdenum content, it is less costly than Alloy C276. Among the places where 2205 Duplex is used include pressure vessels, heat exchangers and scrubbing systems.

Super Duplex 2507 is designed to handle highly corrosive conditions and where high strength is required. The high molybdenum, chromium and nitrogen content in Super Duplex 2507 helps the material withstand pitting and crevice corrosion.

They also have excellent resistance to corrosion cracking and localized corrosion such as pitting, intergranular and crevice. Unlike other standard austenitic steels, UNS S31803 steel has excellent magnetic properties.

The applications include high corrosive applications including acidic applications due to the material composition.

Duplex 2205 has higher resistance to crevice and erosion corrosion than sus316L austenitic stainless grades.

The advantage of combining ferritic and austenitic grades is that the resultant metal has a metallurgical structure that consists of two phases and therefore benefits from the properties of both microstructures. These properties make duplex steel highly sought after in heavy industries, like oil and gas nuclear and chemical processing.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

2205 duplex stainless steel is a cost effective solution for many applications where the 300 series stainless steels are susceptible to chloride stress corrosion cracking. Stress corrosion cracking occurs when stainless steels are subjected to tensile stress, while in contact with solutions containing chlorides. Increasing temperatures also increase the susceptibility of stainless steels to stress corrosion cracking.

Duplex stainless steel is designed to combine improved resistance to stress corrosion cracking (including sulfide stress corrosion cracking), pitting, crevice corrosion and high strength when compared with other stainless alloys.

ASTM A182 F53 Flange is a high strength flange that has 550MPa minimum yield strength and 800MPa minimum tensile strength.

Duplex nuts S31803 also have good fatigue and corrosion resistance in most environmenutal conditions.

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity, and a low coefficient of thermal expansion.

In comparison to SS316, Duplex 2205 has been tested under reverse bending stresses at room temperature. The results show that the fatigue limit/yield strength is about twice as high for Duplex 2205.

Duplex variety stainless steels work well in those applications which contain a high concentration of chlorine. Chloride ions, which are normally detrimental to conventional stainless steels, do not cause any damage to the much stronger Duplex Stainless Steel Pipe. The chemistry of this steel ensures better performance with higher mechanical properties in comparison to austenitic stainless steel pipes.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Due to the excellent physical and mechanical properties of Super Duplex, the quality of Super Duplex steel fasteners can meet the high demands of the gas, oil and marine industries.

With its myriad applications, the process industries are always in pursuit of highly reliable materials. Duplex Stainless Steel Piping is widely endorsed by plant operations management and maintenance specialists who appreciate their toughness and ability to withstand the very aggressive fluids inherent in the process.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

SA 240 UNS S32760 Sheet For ships, tanks and containers, for deployment on most surfaces around metal lattices.

Duplex 2507 has high resistance to chloride stress corrosion cracking, high Strength, and superior resistance to chloride pitting and crevice corrosion.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The chemical composition specifications stated in the norm must be met by the steel Super Duplex Plate. The content, in this case Thick Duplex Alloy 2507 Cold Rolled Sheet, must also meet the required mechanical properties.

ASTM A240 UNS S32760 Plate is a super duplex stainless steel alloy for specific applications.

The notch ductility of SA 240 S32760 Sheet performs well at sub-zero temperatures, down to the -50¡ãC range, while performing well at ambient temperature.

This heat treatment performed on the Duplex 2205 Pipe must be keeping with accordance to the specified temperature and quench conditions.

Duplex 2205 stainless steel (ferritic and austenitic) is widely used in applications requiring good corrosion resistance and strength. Grade S31803 stainless steel was modified several times to form UNS S32205, which was recognized in 1996.

The 2507 pipes could also be electric fusion welded. The Pipes Manufacturer comes under five different classes with each class having a special mechanical property setup. The electric resistant welded pipes are stronger and they could be used for extensive welding.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”