2507 super duplex stainless steel seamless pipe

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Hastelloy B2 resists the formation of grain boundary carbide precipitates in the weld heat-affected zone, making it suitable for most chemical process applications in the as-welded condition. The heat-affected weld zones have reduced precipitation of carbides and other phases to ensure uniform corrosion resistance.
Alloy B2 also has excellent resistance to pitting and stress corrosion cracking.Steel pipes can be disintegrated on the basis of its application.Typical applications of steel pipes are in the area of water pipelines, industrial water lines, oil pipe lines, cross country pipe line, agriculture and irrigation pipes ,tube lines for natural gas, chemical industries, automobile industry, construction industries and other purposes.

Stainless Steel 316L tube is made of austenitic stainless steel with chromium, nickel and molybdenum in its composition, with a carbon content lower than grade 316. The low carbon content of the pipe makes it easier for welding applications.

S32750 is used for marine applications, flue gas scrubbing equipment, and pulp & paper mill equipment.

Stainless steel WNR 1.4550 washers have serrations that extend radially inward or outward to bite into the bearing surface. If a flat washer is required to span a large hole in the assembly, a nyloc nut (nylon insert) must be used. 347 stainless steel washers are austenitic stainless steel washers made from an alloy containing chromium, nickel, molybdenum and nitrogen with limited carbon content. Stainless steel 347 gaskets are used in corrosive environments.

ASME SA182 SS 316 Weld Neck Flange
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

A standard AMS 5666 or UNS N06625 variant of Inconel 625 may contain 58% nickel, 22% chromium, and 3.5% niobium.

Alloy C276 Coils are often used in Pollution control, chemical processing, Waste treatment, Marine engineering, Pulp and paper production, and more.

Alloy B2 pipe bend provides resistance to pure sulfuric acid and a number of non-oxidizing acids.

304/304L stainless steel sheet is often used in cold forming operations during the application process. Its cold forming performance is an important technical indicator to measure whether the forming is smooth and the yield rate. The influencing factors of cold forming of 304 stainless steel are more complicated. As far as its metallographic factors are concerned, it is mainly the composition of the steel, that is, the ratio of chromium equivalent to nickel equivalent, and the elongation of conventional tensile properties is an important characterization index. In order to obtain good cold forming properties, the ratio of chromium equivalent to nickel equivalent in the steel needs to be controlled within an appropriate range.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.25

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

Due to the molybdenum and copper content, alloy 825 plate makes the alloy resistant to reducing agents and acids. Chromium provides oxidative resistance to conditions such as nitrates and oxidizing salts and nitric acid solutions. It offers excellent corrosion resistance through phosphoric and sulfuric acid and is generally the most cost-effective alloy for sulfuric acid service.

Flanges made of stainless steel are called “stainless steel 304 flanges”, also referred to as “SS 304 flanges”. Common material standards and grades include ASTM A182 Grade F304/L and F316/L, with pressure ratings of 150 to 2500 and 300 to 600, respectively.

Each of 304l stainless steel pipe formulations have a degree of corrosion resistance that exceeds that of ordinary steel.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Hastelloy fasteners such as bolts, screws, nuts and threaded rods are ideal for use in a variety of moderately to severely corrosive acid environments. The most common grade of Hastelloy fasteners is Hastelloy C276 (2.4819), which is one of the most versatile corrosion-resistant nickel alloys, surpassing Inconel or Monel. There are also other special grades of Hastelloy fasteners that can address more niche corrosion problems.

ASTM a403 wp304 pipe bend is done to under control conditions to avoid carburization, decarburization and scaling surface. Heat treatment methods are stress relieving, hardening and annealing which strength the ductility and corrosion resistance properties.

300 series grade stainless steel is a chromium-nickel alloy that is manufactured into a range of products including stainless steel tubes and steel pipes. Both 304 and 316 steel pipe is durable enough to maintain its strength at high temperatures, resist corrosion, and is easy to maintain. The choice between material is highly dependent upon how you will use the pipe and the environment in which the pipe will be installed.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

As a global leader in the supply and distribution of duplex 2205 round steel, our steel is used in oil and gas, hydropower, pressure vessels, pulp and paper, structural components, chemical tankers and many other industrial applications.

904l stainless steel plate is a super austenitic stainless steel that provides moderate to high corrosion resistance in a variety of environments. A mixture of chromium and nickel content, along with the addition of molybdenum and copper, provides excellent corrosion resistance. With nickel 25% and molybdenum 4.5%, ASTM B625 UNS N08904 provides good resistance to chloride stress corrosion cracking, pitting and general corrosion, which are superior to 316L and 317L.

Inconel 718 is a nickel-chromium precipitation hardening alloy that maintains good ductility and high strength at temperatures up to 1300°F.

ASTM A182 F304 Flanges
?The?ASTM A182 F304 Flanges?could be cleaned easily with a mild detergent. Despite undergoing repeated cleaning processes, these flanges won¡¯t wear away, an ability it exhibits due it its good wear resistance properties. Moreover, since grade 304 is an alloy that can be easily formed into various shapes, it is easily manufactured into any type of?ASME SA182 F304 Pipe Flange?such as a weld neck flange or an?Inox 304 Slip On Flange.

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

304 stainless steel plate is comprised of at most 0.08% carbon. 304 stainless steel plate also includes at most 2.0% manganese and 0.75% silicon.

It is resistant to a wide range of corrosive media. The chromium content gives better resistance than Alloy 200 and 201 under oxidizing conditions, at the same time the high nickel gives good resistance to reducing conditions.

Controlled chemical composition limits are applied in the nuclear industry to eliminate the risk of stress corrosion cracking by high purity water containing chloride ions.

Inconel 625 is a nickel-based alloy, but its high strength capabilities are due to the addition of molybdenum and niobium on its nickel-chromium matrix. Inconel 625 is also, therefore, resistant to a wide range of corrosive environments of unusual severity.

Common in the plumbing industry, threaded fittings are gateway connections used to increase and fix pipe lengths.

Alloy C276 is increasingly used in aggressive or corrosive environments where other alloys fail.

Hastelloy B3 fasteners are an excellent choice for bolting applications in chemical processing units because the alloy has excellent resistance to hydrochloric and sulfuric acids, while maintaining mechanical strength at elevated temperatures. HT PIPE offers all types of bolts, screws, studs, threaded rods, nuts, washers and custom bolts in Hastelloy B3.

Stainless seamless tubing is the preference when critical applications call for higher working internal pressures and enhanced corrosion resistance in extreme environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20