2 inch 17-4ph plate flanges S17400 flange

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

carbon steel a105 flanges covers seamless forged carbon steel piping components for use in pressure systems at high-temperature service and ambient.Heat treatment is not a compulsory for asmesa 105 flange material except for above Class 300, flanges of special design where the design pressure or design temperature are not known and for items over 4¡± NPS and above Class 300.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

Forged ASME B16.36 Flanged Pipe Fittings Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

ASTM A182 F9 alloy steel round bars can be customized according to customer requirements. They are widely used in automotive and other fields due to their excellent quality and unparalleled functionality.

The formation of ASTM A479 duplex steel UNS S32205 tie rod consists of a pool of austenite surrounded by continuous ferrite phases. ASME SA 479 Duplex Steel UNS S31803 Tie Rods are hot worked in the temperature range of 1750¡ãF to 2100¡ãF. This is designed to reduce the depth used in fabrication, thereby reducing the weight of precise significance for items such as pressure vessels, structural functions, etc. As ASTM A479 dual phase steel for bridges, storage tanks, etc. UNS S32205 rebar has approximately twice the superior performance of SS 304 .

Hastelloy C276 Flanges Hastelloy C276 Flanges are made up of the nickel chromium molybdenum alloy that is called hastelloy. The composition includes 50.99% nickel, 14.5% chromium, 15% molybdenum and carbon, manganese, silicon, sulfur, cobalt, iron and phosphorus in it. The Hastelloy C276 Flanges have high melting point of 1370 degrees Celsius. This high melting point allows for higher operating temperatures of the flanges. The material also has 790MPa minimum tensile strength and 355MPa minimum yield strength.

Alloy 601 Slip On Flange nconel 601 is a nickel-chromium alloy used for applications that require resistance to corrosion and heat. This nickel alloy stands out due to its resistance to high temperature oxidation, remaining highly resistant to oxidation through 2200¡ã F. Alloy 601 develops a tightly adherent oxide scale which resists spalling even under conditions of severe thermal cycling.

Inconel 718 is a nickel-chromium-molybdenum superalloy designed to resist a variety of severe corrosive environments, crevice corrosion and pitting corrosion. This nickel alloy also exhibits extremely high yield, tensile and creep rupture properties at elevated temperatures. Inconel 718 is intended for long-term use from low temperatures to 1200¡ãF.

HT PIPE manufactures and distributes a wide range of carbon steel fasteners including u-bolts, studs, carriage bolts and more. Carbon steel is a common material for fasteners due to its good tensile strength and ability to withstand loads. It responds well to heat treatment with minimal work hardening and brittleness.

Inconel 718 flanges are also available to our customers in different sizes and shapes. These Inconel 718 Socket Weld Flanges are also used in jet engines, pump bodies and parts, rocket engines and thrust reversers, nuclear fuel element gaskets, hot extrusion tools and more.

SME B16.47 317L Pipe Flange hardenability will be reduced if constant feeds and low speeds are used. 317L Stainless steel Flanges can be welded using fusion and resistance methods. In Grade 317 Stainless Steel Pipe flange oxyacetylene welding method is not preferred for this alloy. ASTM A182 SS 317L Slip On Flange does not react to heat treatment. A182 F317/F317L Flange can be hardened by cold working.

Steel Plate are often used for structural and construction applications, pressure vessels, marine and offshord equipment, and military applications. The grade, elements and parameters of a steel plate are also important in how it is used.
Steel plates are classified by thickness: thin plate, medium plate, thick plate and extra-thick plate.
Thin steel plates are steel plates with a thickness between 0.2-4mm produced by hot rolling or cold rolling, and thick steel plates are those with a thickness of more than 4mm
The general name of the good board.
Thin steel plate refers to a steel plate with a thickness of not more than 3 mm. The commonly used thin steel plate thickness is 0.5-2MM, which is divided into sheet and coil supply. Thin
The steel plates are generally B-type steels, cold-rolled or hot-rolled steel plates with steel grades B0-B3. Requirements for thin steel plates: smooth, smooth surface, thick
The degree of uniformity, allowing a tight iron oxide film, must not have cracks, scarring and other defects. The process is divided into hot rolled sheet steel and cold rolled sheet
plate. Mainly used in Changlin Dongfeng fans, automobiles, electrical equipment, vehicles, agricultural machinery, containers, steel furniture, etc.
Thick steel plates refer to steel plates with a thickness greater than millimeters. Thick steel plate is divided into extra-thick steel plate and medium-thick steel plate.
Medium and heavy steel plates refer to steel plates with a thickness greater than 3 mm and less than 50 mm. Medium and thick steel plates are mainly used in shipbuilding, boilers, bridges
Armor and high-pressure vessel shells, etc.
Extra-thick steel plate refers to a steel plate with a thickness of not less than 50 mm. Extra-thick steel plates are mainly used in shipbuilding, boilers, bridges and high-pressure vessel shells
blog.

Alloy 22 (UNS N06022) is the most versatile Nickel Chromium Molybdenum Tungsten alloy with controlled Iron. Due to Alloy 22’s content this alloy exhibits excellent resistance to both oxidising and reducing acid environments as well as those containing mixed acids.

Carbon steel pipe is the most common use piping material in different industries served for construction, structural, liquid transmissions for water, oil and gas. Typical carbon steel pipe material grades in API 5L Grade B, X42 to X70, ASTM A106 B, ASTM A53 B, ASTM A252 Grade 3 and ASTM A333 Grade 6 etc.Mineral and slurry pipe is for the line pipe that applied in mining industries. A slurry pipeline is designated to transmit ores (Iron, Coal materials), or the industry mining waste, we called the pipeline as taillings. And generally these steel pipes connected in a long distances. Above materials mixed with water, we call slurry. People will use pumps to transport to the final destination then water will be filtered out. Since slurry contained different materials some with abrasive properties, so the pipe could be coated with 3PE, FBE layers to against from corrosion.
Both carbon steel pipe in seamless or welded could be used for the transmission of the slurry. So there is a wide range of material and standards available options to suit for the special working conditions.

The grade is non-magnetic in all conditions and has excellent formability and weldability. The austenitic structure also gives this grade excellent toughness, even down to cryogenic temperatures.

SAE 304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel. It is less electrically and thermally conductive than carbon steel. It is magnetic, but less magnetic than steel. It has a higher corrosion resistance than regular steel and is widely used because of the ease in which it is formed into various shapes.[1]

904L stainless steel bolts are non stabilised austenitic stainless steel bolts manufactured from alloy containing chromium, nickel, molybdenum and nitrogen with restricted carbon content. Stainless Steel 904L bolts are used for low temperature service and highly corrosive environments

As with most piping considerations, understanding the ideal uses for bent pipe in your design or project is essential to the proper operation of the finished system.

Type 304 stainless steel is a T 300 Series Stainless Steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium-Nickel austenitic alloy.304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws,[3] machinery parts, utensils, and exhaust manifolds. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features. It is also a common coil material for vaporizers.

We supply ASTM A182 F11 long butt weld flanges with niobium and titanium added to the mining, construction, rail and aerospace industries for sensitization resistance and maximum strength. We closely monitor market trends and needs to invent new, sustainable and economical products that can be customized. Our products are fully certified and 100% durable.

Compared with ferritic stainless steel and austenitic stainless steel, duplex stainless steel pipe has good welding performance. It is neither like the welding heat affected zone of ferritic stainless steel, because of the grain coarsening, the plastic toughness is greatly reduced, nor like austenitic stainless steel, it is more sensitive to welding hot cracks.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

“Duplex” describes a family of stainless steels that are neither fully austenitic (like 304 stainless steel) nor pure ferritic (like 430 stainless steel). The structure of the S31803 duplex stainless steel consists of a pool of austenite surrounded by a continuous ferrite phase.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.63

ASTM A105 Pipe Flanges are known to deliver exceptional performance and are generally developed for meeting the demands. We offer a broad range of ASTM A105 Carbon Steel Flanges through a worldwide network of stock-keeping branches.

Alloy B2 also has excellent resistance to pitting and stress corrosion cracking.

The rim has numerous holes drilled into it that enables the flanged to be attached to a bolted flange. This design is far better because of the structural valve.

HT PIPE offers all 254 SMO Straight Pipes, SMO 254 Pipes for the Oil & Gas and Refinery Industry in the form of 254 SMO Square Pipe, 254 SMO Round Pipe, 254 SMO Hexagonal Pipe, and 254 SMO Hollow Pipe.

Stainless steel SS UNS S30400 Slip on Flanges is a high resistance corrosion steel and it is an austenitic stainless steel with superior resistance as compare to the type or grade 316l and type 317l. Due to addition of some elements this material display a brilliant corrosion resistance against reducing acids such as sulfuric acids. It is used in plants and widely used in various different kinds of applications.

It is available in materials of ASTM A 182, and ASTM A 105. The flanges are available in various grades like ASME B16 47 ¡®A¡¯ Series, and ¡®B¡¯ Series to suit the needs of the clients and the industry.

Solid solution heat treatment: the alloy is heated to a high temperature single-phase region and maintained at a constant temperature, so that the excess phase is fully dissolved into the solid solution, and then rapidly cooled to obtain a supersaturated solid solution.