steel rebar 1.4462 duplex bar steel round prices S31803 bar

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

The applications include high corrosive applications including acidic applications due to the material composition.

ASTM A240 Type 2205 Duplex Sheet provides a maximum Brinell hardness value of approximately 290 in the annealed condition.

Duplex steel flange also offers Good weldability and workability, High energy absorption and Low thermal expansion.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

2205 dual-phase steel fasteners have some excellenut mechanical properties, which may be due to the balanced austenitic and ferritic microstructures in the alloy.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The machinability of 2205 steel pipe is low due to its high strength. The cutting speeds are almost 20% lower than that of grade 304.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity, and a low coefficient of thermal expansion.

Duplex 2205 flanges offer good sulfide corrosion resistance, as well as chloride pitting and crevice corrosion resistant superior to 317L.

If the 22cr Duplex Pipe is to be welded, no filler metal is required to be added to the alloy during its welding process.

The content of chromium, molybdenum, nickel and nitrogen in the 2205 duplex bolt alloy enhances its mechanical properties. E.g. ¨C UNS S31803 Fastener alloys contain trace amounts of carbon.

The high chromium, molybdenum and nitrogen content of 2205 provides better corrosion resistance than common stainless steels such as 316L and 317L in most environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.54

Duplex 2205 round steel contains 22% chromium, 3% molybdenum, and 5-6% nickel. In addition to excellent impact toughness and high strength, it also has high general, local and stress corrosion resistance.

SA 182 F53 S32750 Flange is a super duplex stainless steel supplied in the hot worked and solution annealed condition.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Designers may have the option to reduce the wall thickness of the duplex 2205 welded pipe, because of its high yield strength. The yield strength of this material is almost two times that of the usually used austenitic stainless steel grade. Unlike austenitic steel pipe, the Duplex 2205 Tube may at times exhibit magnetic behavior because the microstructure of its alloy contains about 50% ferrite.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex plates have a two-phase or two-phase microstructure. The microstructure of the duplex steel S32205 foil consists of equal proportions of ferrite and austenite.

The Duplex Pipes are used in high temperature applications along with the Duplex stainless steel tube as well. There are different shapes and sizes of these pipes.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Alloy 2205 UNS S32305/S31803 is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed Duplex Stainless Steel Pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

S32760 super duplex stainless steel is more resistant to pitting and crevice corrosion than regular austenitic or duplex stainless steels and is suitable for use in corrosive environments. This is due to higher additions of chromium, molybdenum and nitrogen.

Duplex 2205 bolts (EN 1.4462 ) are made of austenitic-ferritic stainless steel and are designed to provide higher strength and corrosion resistance than 300 series stainless steels. It helps users avoid stress corrosion cracking common to 316 and 317. Duplex 2205 bolts combine the stress corrosion cracking resistance and high strength of ferritic alloys with austenitic fabrication capabilities.

The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of applications, there are some important technical weaknesses in both types.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex stainless steels are Fe-Ni-Cr alloys consisting of ferritic-austenitic microstructure at room temperature. These steels generally possess beneficial combinations of the austenitic and ferritic phases. Duplex stainless steels exhibit greater toughness and better weldability than ferritic stainless steel (Nilsson, 1992). They have higher strength and better corrosion resistance than austenitic stainless steel (Atamert and King, 1992). Their good engineering performance has led to an increasing number of applications, mainly in corrosive environments such as sour gas pipelines and chemical reaction vessels.
Duplex stainless steels combine characteristics of the austenitic and ferritic family of alloys to offer benefits from both with fewer downsides — often at a lower cost than other steel alloys.
Duplex stainless steels have a combination of two phases, ferrite and austenite in approximately equal measure. This allows them to benefit from the advantages of both austenitic and ferritic stainless steels, leading to increased strength, improved weldability, higher toughness and resistance to several types of corrosion.

The round and hollow pipes are usual ones. In addition to the Duplex Stainless Hollow Pipes and the Duplex Steel Round Pipes there are square, rectangular and hexagonal pipes available in the market.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex steel UNS S32205 round bar has excellent corrosion resistance and resistance to localized corrosion such as intergranular corrosion, crevice corrosion and pitting corrosion.

Super Duplex UNS S32760 is one of the most common super duplex grades on the market. UNS S32760 is a duplex stainless steel designed for use in corrosive chlorine-containing environments, with the addition of W and Cu compared to UNS S32750.

ASTM A240 UNS S32760 Plate is a super duplex stainless steel alloy for specific applications.

The properties of S31803 nuts are even double those of standard austenitic grades.

Super Duplex Steel UNS S32760 are dual phase austenitic-ferritic duplex fasteners manufactured from alloy containing chromium, nickel and molybdenum with restricted carbon content and minimum PREN42. Zeron washers have high strength, resistance to pitting, stress corrosion cracking, erosion and corrosion fatigue, crevice corrosion resistance.

DIN 933 technically ranges from M1. 6 to M52, whereas ISO 4017 ranges from M1. 6 to M64. Secondly, that’s it really, the DIN 933 and ISO 4017 standards are the exact same with the exception of M10, M12, M14 and M22.