2205 duplex

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Inconel 718 Nuts, also known as Alloy 718, are a precipitation hardening (also known as age hardening) form of Inconel 625. This heating and quenching process is used to change the atomic structure of the alloy, making it stronger by locking the metal’s grain structure in place. Additional strength can be obtained by cold working.

SS 316L seamless pipe fittings possess greater durability under pressure and higher aesthetic appeal than its less expensive welded counterpart.

Inconel 718 plate suppliers point out that, in addition to relatively good weldability, this alloy has good formability and excellent low temperature properties compared to other precipitation hardening nickel-based alloys.

Purple firmware, also known as standard parts in the market, is a general term for a type of mechanical parts used to connect two or more parts (or components) into a whole. It is characterized by a wide variety of specifications, different performances and uses, and a high degree of generalization. Fasteners are the most widely used mechanical basic parts and are in great demand.
A fastener is a hardware device that mechanically joins or affixes
two or more objects together. In general, fasteners are used to
create non-permanent joints; that is, joints that can be removed or
dismantled without damaging the joining components.

These pipe fittings include Tee, Concentric reducer, eccentric Reducer, 5D/6D bend, elbow, unions, plugs, cross tee, pipe cap and nipple, ect for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

Stainless Steel 904L Flange is a method of connecting pipes, valves, pumps and other equipment to form a piping system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal.

Astm A312 Tp 904l is also resistant to crevice corrosion and stress corrosion cracking. Stainless Steel 904l Seamless Pipe offers excellent formability and weldability and is said to be non-magnetic. Moreover, Astm A312 Tp 904l Welded Pipe is said to be resistant to chloride attacks and warm seawater.

Type 304 is the most popular stainless steel and is a natural choice for its corrosion resistance. It resists rusting in many different environments, but is primarily attacked by chlorides.

ASTM B564 601 Raised Face Flange nconel 601 is a nickel-chromium alloy used for applications that require resistance to corrosion and heat. This nickel alloy stands out due to its resistance to high temperature oxidation, remaining highly resistant to oxidation through 2200¡ã F. Alloy 601 develops a tightly adherent oxide scale which resists spalling even under conditions of severe thermal cycling.

ASTM A234 WP9 Alloy Steel Pipe Fittings are known to deliver exceptional performance and are generally developed for meeting the demands.Extraordinary safeguards for these Alloy Steel WP9 Dish Cap Butt Weld Pipe Fittings ought to be taken to stay away from intemperate heat input.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Grade B7 is a heat-treated chromium-molybdenum low-alloy steel with minimum tensile strength requirement of 125 ksi (860 Mpa), yield 105 ksi (720 Mpa), and maximum hardness of 35HRC.

ASTM A193 Grade B8M Grade 1 Fasteners are similar to Grade B8 but are made of AISI 316 stainless steel instead of AISI 304 stainless steel. Type 316 stainless steel has better corrosion resistance than type 304 stainless steel due to the addition of molybdenum.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

C-276 alloy has excellent resistance to pitting and to stress-corrosion cracking. It is also one of the few materials that withstands the corrosive effects of wet chlorine gas, hypochlorite, and chlorine dioxide.

The SS UNS S31000 Flanges are used to close a connection. These flanges can also come in different face types such as raised face, flat face and ring type joint flanges. Please contact us for more information on the flanges and their prices in the 310 range.

ASTM B564 Inconel 718 Threaded Flange Grade 718 Inconel Flange is the most common grade of the hardenable Inconel. This precipitation-hardened nickel-chromium alloy combines outstanding corrosion resistance and high strength at elevated temperatures. The alloy is an about 2x as strong as Inconel grade 625 having excellent creep-rupture strength at temperatures to 1300¡ãF (700¡ãC) and usable up to 1800¡ãF (982¡ãC). Inconel grade 718 is often used in gas turbines, rocket motors, spacecraft, nuclear reactors, pumps, and tooling.

This stainless steel is considered for a wide variety of applications on good corrosion resistance, ease fabrication, excellent formability, and high strength with low weight.

Annealing softening begins at approximately 1600¡ãF (871¡ãC) and is fairly complete after 10 to 15 minutes of heating at 1800¡ãF (982¡ãC). Above this temperature, grain growth can be objectionable, although very brief heating at 1900¡ãF will result in complete softening without excessive grain growth. Since the cooling rate has no effect on softening, the material can be water quenched or air cooled.

There are different types such as socket weld flanges, welded neck flanges, Inconel 601 Slip On Flanges, orifice flanges and so on. The flanges made of this material are strong, corrosion resistant to acids, reducing agents and oxidation and are also harder.

Inconel X750 is considered to be a popular and cost-effective nickel-chromium superalloy.The most notable characteristic X750 exhibits is its high strength in cryogenic temperatures making it essential to industries that make use of gas turbines, pressure vessels, and rocket engines.

316l has excellent forming and welding characteristics. It is easily braked or rolled into various parts for use in industry, construction and transportation.

These ASTM A182 alloy steel F5 F9 F11 F12 F22 F91 pipe fittings are corrosion resistant. ASTM A182 alloy steel F5 F9 F11 F12 F22 F91 fittings also have high dimensional accuracy.

Duplex 2205 pipe is stainless steel. It belongs to a family of stainless steels called duplex steels. There are different groups of this material. This series of pipes can be cold drawn, hot rolled and welded. Alloy 2205 seamless tube is cold drawn, it has less absolute roughness.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.39

Inconel 625 elbow is made of high-performance nickel-chromium-molybdenum alloy known for its high level of strength, temperature resistance, and corrosion resistance.

The carbon steel gets its mechanical properties and physical properties from this material composition. The Carbon Steel A350 LF2 Flanges have a minimum tensile strength of 485MPa and a minimum yield strength of 250MPa. The material is also hard with a 197 HB Brinell hardness score. There are class 1 and class 2 product level specifications in these flanges.

INCONEL C-276 alloy has excellent resistance to a wide variety of chemical process environments, including strong oxidizers such as ferric and cupric chlorides, hot contaminated media (organic and inorganic), chlorine, formic and acetic acids, acetic anhydride, and seawater and brine solutions.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Nickel alloys are some of the most useful materials for manufacturing technically superior pipes and tubes for industrial applications. Their inherent properties make them viable for a wide range of uses. Nickel alloys are exceptionally corrosion resistant and can be used in high-temperature environments.