310s stainless steel welded pipe

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

A wide range of industries, shops and systems rely on high-performance flanges, and custom pipe flanges are often critical to getting the job done right.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Because carbon steel flat wahsers still have a lot of carbon in them that oxygen would prefer to bond with. Chromium in carbon steel lock washers also induces ferromagnetism in the steel, which is not desired in some applications, and nickel also helps with this.

Monel 400 is used in process vessels, heat exchanger piping, and gasoline and potable water storage tanks in the marine sector. The non-sparking properties of this alloy make it suitable for high-risk situations in the explosives industry, rockets and pulp and paper industries.

The weld neck flange comprises of a round fitting that extends beyond the rim of the circumference. These flanges, typically manufactured from forging, are actually welded to pipes.

These alloys typically comprise of about 1 % to 5% of the steel’s content and are usually added based on their ability to provide a very specific attribute for their end use.

Machining of Hastelloy UNS N10276 polished plates is best done in the annealed condition. Since this particular alloy grade is prone to work hardening, only low cutting speeds are required.

Stainless steel WNR 1.4550 washers have serrations that extend radially inward or outward to bite into the bearing surface. If a flat washer is required to span a large hole in the assembly, a nyloc nut (nylon insert) must be used. 347 stainless steel washers are austenitic stainless steel washers made from an alloy containing chromium, nickel, molybdenum and nitrogen with limited carbon content. Stainless steel 347 gaskets are used in corrosive environments.

316L, however, is a better choice for a project that requires a lot of welding because 316 is more susceptible to weld decay than 316L (corrosion within the weld).

Although 316L contains less carbon, 316 and 316L stainless steels cost approximately the same.

INCOLOY alloys belong to the category of super austenitic stainless steels. These alloys use nickel-chromium-iron as the base metal and add additives such as molybdenum, copper, nitrogen and silicon. These alloys are known for their excellent strength at high temperatures and good corrosion resistance in a variety of corrosive environments.

304 and 304L can be specified in annealed conditions with very good formability. Higher nickel versions can be specified for enhanced multi-stage deep drawing characteristics. For spring type applications, Types 304/304L can also be specified in higher strength cold work conditions. Type 304/304L is non-magnetic in the annealed condition, but may become slightly magnetic by cold working.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Stainless steel flange simplified as SS flange, it refers to the flanges that made of stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500. It used in more industries than carbon steel as stainless steel has better resistant performances on corrosion environment and always provides with a good appearance.

The best machinability for these Monel K500 Lap Joint Flanges is in the annealed condition. Meanwhile, these Monel K500 Socket Weld Flanges are also being offered in different sizes and shapes to our customers.

Incoloy 800HT is further modified with titanium and aluminium combined levels (0.85-1.20%) to ensure optimum high temperature performance. Nickel alloys are double certified (800H/HT) and combine the properties of both forms.

Alloy X pipe bend specimens showed no carburization at all. Of ten materials evaluated in an atmosphere of hydrogen, nitrogen and ammonia at 1100 Deg. F. and 25,00 psi for 64 days, Alloy X had a nitride case less than one-fourth as thick as the closest competitive material without intergranular attack.

Hastelloy C-276 alloy can be forged, hot-upset, and impact extruded. Although the alloy tends to work-harden, it can be successfully deep-drawn, spun, press formed or punched.

The specification for standard ASTM A182 F9 Flanges covers both forged or Rolled Alloy Steel Pipe Flanges & Fittings, that have been designed and manufactured for high temperature service. ASTM A182 F9 Flanges have a minimum chromium content of 18% in the alloy. This makes it survive in temperatures up to 870 degrees Celsius.

If your outdoor appliance enclosure is rusted, not only is there a danger of exposing all critical electrical components inside, but it can be expensive to replace in the event of a short. We’re talking about parts damage and replacement, repair costs, including labor and downtime. I’ve seen some real horror shows when the shell is rusted. We have found that using 316 stainless steel instead of 304 stainless steel on outdoor enclosures that will be exposed to various elements, such as oil rigs, not only increases the life of the enclosure, it is also safer.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.43

Though it is important to keep in mind that pitting corrosion can be a concern in chloride solutions when oxidizing media is present. In these conditions, the passive (protective) layer of the Duplex 2205 material may be compromised in localized pitting may occur.

Environments that don¡¯t attack 304/304L stainless steel will normally not corrode 317L.

ASME SB564 Alloy 601 weld neck flanges nconel 601 is a nickel-chromium alloy used for applications that require resistance to corrosion and heat. This nickel alloy stands out due to its resistance to high temperature oxidation, remaining highly resistant to oxidation through 2200¡ã F. Alloy 601 develops a tightly adherent oxide scale which resists spalling even under conditions of severe thermal cycling.

A350 Gr Lf2 grade is widely used in the manufacture of flanges and fittings.

304 also contains 8-10.5% nickel (Ni). It is added to make the austenite structure more stable at room temperature. Nickel also improves high temperature oxidation resistance, making the steel resistant to stress corrosion cracking. Where the steel is to be stretch formed, a lower percentage (8%) of nickel should be chosen. Higher percentages are better (9% or more) if the steel is to be deep drawn.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.34

UNS N08825 Flange Incoloy 825 Flanges are one such type of flanges that have outstanding resistance to oxidizing as well as reducing acids. They are fabricated to improve their resistance to corrosion and are clean to weld

ASTM A182 Alloy Steel Blind Flanges is a solid disk used to block off a pipeline or to create a stop. It has mounting holes around the perimeter and the gasket sealing rings are machined into the mating surface.

SS 316L/316Ti Blind Flanges
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

The flanges also come in B16.5, B16.47 and other standards and dimensions. The Alloy Steel Flange Material can vary according to the chemical composition.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.