rugged design GR.70N bleed ring

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

AL-6XN alloy (UNS N08367) is a low carbon, high purity, nitrogen-bearing ¡°super-austenitic¡± stainless alloy. The AL-6XN alloy was designed to be a seawater resistant material and has since been demonstrated to be resistant to a broad range of very corrosive environments.

C276 has good fabricability and impressive corrosion resistance in some of the most severe environments.

ASTM A182 Grade F316 Socket Weld Flanges
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

Grade 904L is less resistant to nitric acid than grades 304L and 310L, which are free of molybdenum. This steel grade needs to be solution treated following cold working, to achieve maximum stress corrosion cracking resistance under critical environments

The flange connection type usually comes with a double unit, with washers and some bolts and nuts to connect to each other. (The pipe is welded on the flange first, and then the valve and other equipment are installed on the flange.) When connecting these parts, put the gasket between the two flanges, and then tighten the flange screws so that the two are tightly connected together. Flange connection is convenient, flexible and labor-saving. When the pipeline is repaired, the screws on the flange can be removed, and the corresponding pipeline or valve can be removed. Also replace with new pipes and valves.

SS 304 Tubes offers some highest putrefaction deviation to a great deal of industrial milieu and chemical corrodents. Meanwhile, our Stainless Steel Cold Drawn 304 Tubes have an amazingly improved formability and can be welded all the way through high-quality refinement by all standard ways
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Reactor vessels and heat exchanger tubing used in the production of vinyl chloride.

Stainless steel 304l gets its name because of the interaction between its alloying composition and the environment to which they are exposed to resist rusting. Many types of stainless steel have multiple uses and there is a lot of overlap. All stainless steels contain at least 10% chromium. But not all stainless steels are created equal.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The composition of stainless steel 304L flanges contains carbon, nickel, silicon, nitrogen, sulfur, manganese, phosphorus and chromium. 304L is available in different grades depending on the carbon content.

Monel K500 fasteners are cold worked prior to precipitation hardening. The strength of the fasteners is stable to 1200 degrees Fahrenheit. Here, at this temperature, it becomes more ductile, reaching toughness around 400 degrees Fahrenheit. Higher strength and hardness after precipitation hardening compared to 400. Due to its numerous advantages, Monel K500 ASTM fasteners are used in a wide range of industries.

Stainless steel is an iron alloy that contains a minimum of 10.5% chromium. Alloying elements such as nickel, molybdenum, titanium, carbon, nitrogen, and copper can boost the strength, formability, and other properties of stainless steel. Different alloys offer different levels of corrosion resistance.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Type 316 steel is an austenitic chromium-nickel stainless steel that contains between two and 3% molybdenum.

Stainless steel 347 reducer has tensile strength and minimum yield strength. Stainless Steel 347 Stub End Fittings are a non-magnetic grade that cannot be hardened by heat treatment, are typically used in the annealed condition, and are known for their ease of fabrication and formability.

In oxidizing conditions, INCONEL 600 has better corrosion resistance than Alloy 200 and Alloy 201.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

These Monel 400 pipes have high strength and toughness over a wide temperature range and have excellent resistance to many corrosive environments.

Alloy steels are used in a range of demanding applications in the aerospace and power (nuclear) industries. Adding other elements gives alloy steel extra strength.

Supplied in the annealed condition, it has a yield strength of 80ksi (550Mpa), which is higher than most austenitic and duplex grades.

ASTM A182 F5 Lap Joint Flanges go by a range of names, including back up flange, loose hubbed flange, loose ring flange and van stone flange. ASTM A182 F5 Flanges is a method of connecting pipes, valves, pumps and other equipment to form a piping system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal.

Super Duplex Steel Stud Bolt is available in lengths ranging from 2mm to 200mm and has high strength values as well. Super Duplex S32750 is the most common duplex ferritic, austenitic stainless steel grade used for producing stud bolts.

Bright Annealed (BA) is produced by heat-treating (annealing) steel with a controlled atmosphere furnace. After heat-treatment, the steel has a reflective, mirror-like appearance, but may also have some imperfections and cloudiness. BA stainless steel can be buffed to attain a more reflective finish, and is often specified for applications where a highly reflective surface is desired.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Nickel alloy 825 seamless pipe is particularly resistant to sulfuric and phosphoric acid. Known as WNR 2.4858 seamless pipe, this nickel steel alloy is used in chemical processing, pollution control equipment, oil and gas well piping, nuclear fuel reprocessing, acid production and pickling equipment.

Duplex2507 thread rod are dual phase austentic-ferritic duplex fasteners manufactured from alloy containing chromium, nickel and molybdenum with restricted carbon content and minimum PREN42. SAF2507 thread rod have high strength, resistance to pitting, stress corrosioni cracking, erosion and corrosion fatigue, crevice corrosion resistance.

Thanks to its special properties, titanium is an ideal material for the construction of exhaust systems in motor sports.

Incoloy Alloy 800 is widely used in equipment that must have high strength and resistance to oxidation, carburisation and other harmful effects of high temperature exposure.

Pipe flange, also known as flange. Flanges are the components in a piping system that connect pipes. Also suitable for connection between two devices (pipe with valve or pipe with equipment).

nconel 600 Flanges are made up of a material that has carbon, manganese, silicon, sulfur, copper, iron, nickel and chromium. This is a nickel chromium alloy as it contains 72% nickel and 14% chromium minimum

Hastelloy B3 Weld Neck Flange is not recommended for use in the presence of ferric or cupric salts because these salts can cause premature failure.

The exceptional corrosion resistance of C22 has promoted its use in many different markets wherever harsh environments are encountered, including the chemical process, pharmaceutical, food processing, oil and gas, power generation, and the paper industries.